Typical Wiring to Diesel Engine
Special Notes: |
|
| properly it should prevent the injection pump from siphoning fuel thus | ||||
• Murphy Pressure Relief Valve; model PRV50 is factory set to start open- | not allowing continued operation after the SV valve closes. |
| |||||
ing at 25 psi (172 kPa) [1.72 bar]. This is done to protect the fuel filter | • Install the | ||||||
canister from bursting due to high pressure. |
|
| pump inlet port. |
|
|
|
|
• Install the Murphy Check Relief Valve, model CKV2336, as close as | • All fittings must be air tight. |
|
|
| |||
possible to the injection pump. When the CKV2336 is installed |
|
|
| WD PANEL |
| ||
|
|
|
|
|
|
| |
|
| DIESEL ENGINE | Battery |
|
|
| |
|
| On some fuel |
| 518PH |
| ||
|
|
|
|
|
| ||
CAUTION: Certain dangers |
| PRV50 | Injector | systems it may |
| B SW SW NC | G |
to human safety and to | Glass | be necessary to | Fuse | ||||
equipment may occur if | Filter | SV |
| install check |
| 2 1 |
|
|
| valve here. |
|
|
| ||
some equipment is stopped without |
| valve |
|
|
|
| |
|
|
|
|
|
|
| |
|
| Injection |
|
|
|
| |
recommended that monitored |
|
| Pump CKV2336 |
|
|
|
|
|
|
|
|
|
|
| |
functions be limited to |
|
|
|
|
| 20P |
|
or to alarm before shutdown. |
|
|
|
| 100 psi |
| |
|
|
|
|
|
| ||
|
|
| Fuel Return Line |
|
|
|
|
|
|
| Fuel |
|
| 20T |
|
|
|
|
|
| 250 F |
| |
Pump
Fuel Tank
Dimensions
(214 mm)
(149 mm)
Mounting
holes 2 places 9/32 (7 mm)
diameter
(71 mm)
(83 mm)
|
|
| Y | S WI | CH | GA |
|
|
| H |
|
| |
|
|
| P |
|
| G |
| M | U | R |
|
| E |
|
|
|
| ® | ||
|
|
|
| P.S.I. |
| |
|
|
| Y | S WI | CH | GA |
|
|
| H |
|
| |
|
|
| P |
|
| G |
M |
| U | R |
|
| E |
|
|
|
| ® | ||
|
|
|
|
|
| |
F
(70 mm)
(87 mm)
Rotating/Tilting Panel
It is the ability of this panel to mount in many different positions (Swichgage instruments can be rotated, the panel tilted) that allows for instrument visibility without a difficult installation or interference with other engine equipment.
WD Panel
|
| HY | S WI | C | HG | Mounting |
|
|
|
| ||||
| U |
|
|
|
|
|
| |||||||
| R |
|
| E |
|
|
|
| ||||||
|
| P |
|
| AG |
|
|
|
|
|
|
|
|
|
M |
|
|
|
| ® | Surface |
|
|
|
|
| |||
|
|
| P.S.I. |
|
|
|
|
|
|
| ||||
|
| HY | S WI C | HG |
|
|
|
|
|
|
|
|
| |
|
| P |
|
| A |
|
|
|
|
|
|
|
|
|
| U | R |
|
| G |
|
|
|
|
|
|
|
|
|
M |
|
|
|
| ® |
|
|
|
|
|
|
|
|
|
|
|
| F |
|
|
| HY | S WI | C | HG |
| HY | S WI C | HG |
|
|
|
|
|
|
| P |
|
| A |
| P |
| A |
|
|
|
|
|
| U | R |
|
| G | U | R |
| G |
|
|
|
|
|
|
|
|
| E |
|
| E | ||
|
|
|
|
|
| M |
|
|
| ® | M |
|
| ® |
|
|
|
|
|
|
|
| P.S.I. |
|
|
|
| F |
|
How to Order | Warranty |
To determine the kit that wil suit your application, refer to the Kit Combinations on the reverse side. When you have decided on a kit, the model number and voltage must be specified when ordering. Example: WD100, 12 Volt
Approximate Shipping Weights and Dimensions for each kit are specified on the reverse side of this bulletin, under Kit Combinations. Order oil line assembly separately.
A limited warranty on materials and workmanship is given with this FW Murphy product. A copy of the warranty may be viewed or printed by going to www.fwmurphy.com/support/warranty.htm
www.fwmurphy.com
918.317.4100 Email: sales@fwmurphy.com
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time. MURPHY, the Murphy logo, and Swichgage® are registered and/or common law trademarks of Murphy Industries, Inc. This document, including textual matter and illustrations, is copyright protected by Murphy Industries, Inc., with all rights reserved. (c) 2006 Murphy Industries, Inc.
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
Printed in U.S.A. 12 0 140
