QUICK START
1Connect a twin RCA-to-RCA lead from the L (left) and R (right) Line Output jacks to the corresponding CD inputs on your amplifier.
2Plug in the AC power cord.
3Press the POWER button to turn on the player.
4Press OPEN to open the disc drawer.
5Place a CD, label side up, in the tray’s circular recess. Be certain that the disc is centred within the recess.
6Press PLAY/PAUSE. The drawer closes automatically, and the disc begins to play.
7At any time you may press SKIP ![](/images/new-backgrounds/1036899/368997xi2.webp)
![](/images/new-backgrounds/1036899/368997xi3.webp)
or ![](/images/new-backgrounds/1036899/368997xi5.webp)
to select different tracks on the disc.
8Press PLAY/PAUSE if you want to stop play temporarily while keeping the pickup at its current position on the disc. Press PLAY/PAUSE again when you want to resume playback. Press STOP if you want to end play and reset the pickup to the beginning of the disc.
NOTE ON INSTALLATION
Install the NAD C 521BEE Compact Disc player on a level, vibration-free surface. (Severe vibration, or operation in a tilted position, may cause the player to mis-track.) The player may be stacked with other stereo components, as long as there is adequate ventilation around it. If the player is placed in close proximity to a radio tuner (AM or FM), a VCR, or a television set, the operation of its digital circuits may produce static that would interfere with reception of weak broadcast signals. If this occurs, move the CD player away from other devices or switch it off when viewing or listening to broadcasts.
REAR PANEL CONNECTIONS
1. LINE OUTPUT
Connect a cable from these jacks to your amplifier. Plug one end of a twin RCA-to-RCA lead into the L (upper) and R (lower) output jacks. Connect the other end of the cable to your stereo amplifier’s CD input, or to any other “line-level” input jacks (such as the AUXiliary inputs). Do NOT connect this cable to the amplifier’s PHONO input jacks. The RCA sockets on your NAD C 521BEE are colour coded for convenience. Red and White are Right and Left audio respectively, and yellow for Digital Out. Ensure that leads and sockets are not damaged in any way and all sockets are firmly pushed home.
2. DIGITAL OUTPUT
The digital playback signal is available at this output jack. The serial data output is taken after the error correction but before the digital-to- analogue conversion and filtering. The output is transformer-isolated from the built-in D-to-A circuits. It may be connected to any digital signal processor that conforms to the Sony/Philips (SPDIF) standard.
To use the digital output, connect a cable from this jack to the “CD Digital” or equivalent input on a digital processor or recorder. For best results, the cable should be a 75 ohm coaxial cable of the type used for video signals, with an RCA phono plug at each end. (To distinguish them from similar phono-plug cables used for analogue audio signals, video and digital signal cables often are colour-coded with yellow plugs.)
3. AC LINE CORD
Connect this power cord to an AC mains wall outlet or to an AC convenience outlet at the rear of your amplifier.
FRONT PANEL CONTROLS
1. POWER ON/OFF
Press this button to switch on the power to the disc player. Press again and release to switch the power off. The display will light up to indicate the unit is switched on and ready for use.
2. DISC DRAWER
To play a disc, press the OPEN button to open the disc drawer. Place the CD within the large circular recess in the drawer, with its transparent playing surface facing down. The label must face UP. CD-3 discs (3-inch CD “singles”) can be played without the aid of an adapter. Place the disc in the drawer, centered in the smaller circular recess, with its label facing UP.
NOTE: This player was not designed to accommodate a “damping disc” placed on a CD, nor two CDs stacked together. It plays audio CDs and CD-RW, but not discs identified as CD-V, DVD, CD-I, CD-ROM, or PHOTO CD. Refer also to chapter “A note on CD-R and CD-RW audio discs”
3. DISPLAY
The display provides information about playback status and about the optical pickup’s location on the disc. The displayed track/time information is obtained by reading inaudible “sub-codes” in the disc.
TRACK NUMBER Each disc is segmented into numbered tracks when the recording is made; typically each numbered track will correspond to a different song, symphonic movement, etc. These track numbers are identified on the CD package and are encoded in the disc by its manufacturer. In some CDs, at the manufacturer’s option, tracks may be sub-divided into sections identified by Index numbers. This player does not display Index numbers.
TIME Normally this display shows the time elapsed since the beginning of the current track. Using the TIME button you can switch the display to show the remaining number of tracks and playing time to the end of the disc. When you load a different disc and use the OPEN button (No. 4) to close the disc drawer, the display shows the number of tracks and the total playing time of all the tracks on the disc.
REMAIN REMAIN lights up in the lower-left corner of the display if you have pressed the TIME button to show the remaining number of tracks and time of the disc.
REPEAT 1 “REPEAT” and “1” light up respectively in the centre and upper-left corner during repeat-play of a single track. “REPEAT” and “ALL” light up during repeat-play of the entire program or disc RANDOM When the C 521BEE’s random mode has been selected, “RANDOM” will be shown in the Display Panel.
CALENDAR DISPLAY TRACK LISTING Displays a list of tracks available on the disc. As each track is played its number is blanked out on the Track Listing, giving a simple indication of how much of the disc has been played and how much remains. The number for the current track being played blinks. The display shows up to 16 numbered tracks.
MEMORY During Program Play or programming for Program Play,
MEMORY will light up. | | | | | |
STATUS A right-pointing arrowhead | , located near the left edge of |
the time display, lights up during PLAY. Two vertical bars | | | | indicate |
| | |
| |
that the player is in PAUSE. In STOP mode the display reverts to showing the total number of tracks and playing time of the disc.
no dISC When no disc is present or when you load a disc that cannot be read (because it is dirty or is upside-down) “no dISC” lights up in the display.