4. FM/AM
The FM/AM button switches the tuner section from the AM band to the FM band and
5. FM MUTE / MODE
This button combines two functions; it switches the tuner from FM Stereo to Mono mode and disengages the muting circuitry at the same time. The muting circuit will mute the tuner in between radio stations when searching or tuning. This way the tuning noise is avoided.
Very weak radio station signals however may be suppressed by the muting circuit. if such a very weak station is in stereo it will have a high level of background hiss. Switching to Mono and disengaging the muting circuit by depressing the FM MUTE/MODE button will allow the station to be heard and will cancel most or all of this background noise.
In normal operation the mute circuit is engaged, the display indicates “FM MUTE”. Press the FM Mute/Mode button to disengage the muting circuit and switch from stereo to mono reception. “FM MUTE” will extinguish in the display. Also, “FM STEREO” will extinguish if a stereo broadcast was received. Press the FM Mute/Mode switch again to return to Auto Stereo FM operation.
In combination with the MEMORY button (No. 6) and DOWN/UP buttons (No. 8) a preset number can be emptied. (Refer to the separate chapter “Storing and Recalling Presets” for more information.)
6. MEMORY
The Memory button is used to store stations into the Preset Memory (1- 30 Presets on FM,
Refer to the separate chapter “Storing and recalling Presets” for more information.
7. PRESET / TUNE
The Preset/Tune button toggles between the Preset and Tune mode. When Preset mode is selected, “PRESET” lights up in the display area. Up to 40 Presets, either AM (10 Presets) or FM (30 Presets), can be stored.
Refer also to separate chapter “Storing and Recalling Presets” for more information.
8. DOWN / UP 
AND
The function of these buttons depends on the tuning mode selected with the Preset/Tune button (No. 7). The Preset/Tune button toggles between the two operation modes:
a)Preset mode (indicated in the display area): Press the 
(down)
button to scroll to a lower number Preset; press the 
(up) button to scroll to a higher Preset number. This is a
b)Tune mode: Press the 
(down) or 
(up) button for more than 1/2 second to engage automatic tuning respectively up or down the frequency band. The tuner will search automatically for the first reasonably strong radio station, where it will stop. Press the Down/Up button again for 1/2 second to start searching again.
NOTE
Automatic tuning is available on both FM and AM.
By briefly tapping the 
(down) or 
(up) buttons you can engage manual tuning respectively down or up the frequency band for precise tuning to a specific frequency. With each successive tap of the keys, the tuner will take 0.05 MHz steps on FM so you can accurately tune into the desired frequency.
This tuning mode can also be useful when trying to receive a radio station which is too weak for the auto search mode. When tuned
accurately to a station, “ 
TUNED 
” will light up in the display. Very weak radio station signals however may be suppressed by the muting circuit. If such a very weak station is in stereo it will have a high level of background hiss. Switching to Mono and disengaging the muting circuit by depressing the FM MUTE/MODE button (No. 5) will allow the station to be heard and will cancel most or all of this background noise.
Refer to the separate chapter “Storing and Recalling Presets” for more information.
9. VFL DISPLAY
Vacuum Fluorescent Display. The display area will show all vital information when the unit is operational.
10. VOLUME & SET UP
In the default function, this control acts as a Volume control, adjusting the overall loudness of the signals being fed to the loudspeakers and headphones. Unlike conventional controls, the T742’s volume control doesn’t have a start or end position. Volume can also be adjusted from the remote control handset using the Master Volume Up or Down buttons. The Volume control does not affect recordings made using the Tape, VCR and Video 4 outputs but will affect the signal going to the
– ∍ to +18dB.
On the remote control handset, press the Mute button to temporarily switch off the sound to the speakers and headphones. Mute mode is indicated by “MUTING” flashing in red in the display area. Press Mute again to restore sound. Mute does not affect recordings made using the Tape,VCR and Video 4 outputs but will affect the signal going to the
SVENSKA PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH
11
