Nady Systems warranty Using Your SPC-10, Precautions and Care of Your SPC-10, Service

USING YOUR SPC-10

The SPC-10 can be used with any standard mixer, powered mixer/amplifier, or mic preamp. Using either an XLR to XLR or XLR to 1/4” phone plug low impedance cable, connect the female XLR end to the SPC-10 and the other end (male XLR or 1/4” phone plug, as appropriate) to your equipment.

Depending on the application, the SPC-10 can either be handheld or mounted on a microphone stand with a standard mic clip.

Be aware of the proximity effect (an increase in bass response) when the mic is placed close to the mouth or instru- ment. This may or may not be desirable. Experimenting with the position of the mic with respect to the audio source will ensure the optimum results you are seeking in any given application. Also, never place your hand over the balIscreen of the mic during use, as this can degrade the performance.

If the microphone is placed too near a speaker, an unpleas-

ant howling effect (acoustic feedback) may occur. Although all microphones are prone to feedback to some extent, those with a unidirectional polar pattern (such as the SPC-10) are specially designed to accept only signals from the audio source directly in front of the mic cartridge. Thus, the cardioid pattern of the SPC-10 ensures that it will deliver only the desired audio in front of the mic, rejecting the unwanted audio from the rear, even in noisy ambient conditions with high sound pressure levels from the PA and monitor speakers. This means that feedback will be greatly minimized with the SPC- 10 in all live performance miking applications.

Some useful ways in which to totally eliminate annoying feedback include: experimenting with mic positions with respect to the speakers, decreasing speaker volume (whenev- er possible), and adjusting the equalization of the mic audio with the mixer.

PRECAUTIONS AND CARE OF YOUR SPC-10

•The microphone should never be dropped or subjected to extreme shock. Store only in a padded case to protect it dur- ing transport.

•Keep the microphone away from extremely high tempera- tures (above 140°F or 60°C) and humidity. Avoid leaving the microphone in direct sunlight for long periods of time.

•When using the microphone outdoors, avoid getting it wet.

•After use in a high-moisture application such as a stage per- formance, wipe off the microphone with a dry cloth and per- mit it to air dry. Do not store the unit in a closed space (e.g., a plastic bag) until all moisture has evaporated.

•To protect the mic cartridge and ensure the longest possible useful life, it is highly recommended that for vocal applica- tions, an external foam windscreen be used over the ball grille. This will prevent the buildup of saliva and perspiration on the cartridge diaphragm, which degrades performance and shortens the useful life of the microphone. Such a wind “sock” will also eliminate wind noise when the mic is used in a windy outdoor environment.

FREQUENCY RESPONSE POLAR PATTERN SCHEMATIC

		Capsule's
		bias-voltage filter		Stabilizer
Capsule						Power Output
	High impedance		Low frequency		Follower
			Attenuater
	FET Amplifier				Amplifier	Output Amplifier
			network

2 Output +

1 48V Phantom Power

3 Output

Pin

XLR

SERVICE

(U.S.) Should your Nady microphone require service, please contact the Nady Service Department via telephone at (510) 652- 2411 or e-mail at service@nadywireless.com. (INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you purchased this product.

Date of purchase __________________________________________________________________________________________________________

Dealer’s Name ____________________________________________________________________________________________________________

Street____________________________________________________________________________________________________________________

City __________________________________________State ________________________Zip __________________________________________

Note: Do not attempt to service this unit yourself as it will void your warranty.

SPC-10 SPECIFICATIONS

CARTRIDGE TYPE	Condenser	EQUIVALENT NOISE LEVEL	18dB (A Weighted IEC/DIN651)
DIRECTIVITY PATTERN	Cardioid pattern for optimum feedback rejection	SIGNAL TO NOISE RATIO	76dB
FREQUENCY RESPONSE	30 to 20,000Hz	CONNECTOR	3-pin XLR (gold plated)
SENSITIVITY		POWER REQUIREMENT	+48V phantom power, 2.7mA
(@1kHz, 74dB S.P.L.)	8mV/Pa	MIC CABLE	3-pin XLR standard cable (not supplied)
IMPEDANCE	200 Ω	DIMENSIONS	2.1” Diam. x 7.1” (53 Diam. x 180 mm)
MINIMUM LOAD IMPEDANCE ....	1,000 Ω	WEIGHT	11.5 oz (322 g)
MAXIMUM S.P.L.		MATERIAL	Die-cast zinc
(1% THD @≤ 0.5% @ 1KHz)	140dB	BALLSCREEN	Steel mesh
DYNAMIC RANGE	122dB

Specifications and design subject to change for improvement purposes without prior notice.

08/27/01