Nady Systems U-1000 owner manual System Specifications

3. User Name

The user name field has 12 character spaces.

Choose from upper and lower case alphabet, 27 USER NAME

special characters (including space), and 10RFAF numbers. In the User Name Menu, hold the SET

(7) button for 3 seconds. The curser will blink, press the UP (4) or DOWN (5) buttons to cycle the character selection, press the SET button to advance to the

5

NADY

NADY 1000

2. Company and Model number (can not be edited)

The receiver will remember the last Menu of User Name, Group and Channel, User Edit, or Channel Frequency, when it is turned off. That menu will appear when it is turned on.

Menu pages in Preset or User mode

Cycle Menu pages by pressing the MENU (6) button. USER MODE CYCLE — 1, 2, 3, 5, 6, 7

PRESET MODE CYCLE — 1, 2, 3, 4, 6, 7

USER MODE

1. Preset or User modePRESET MODE In the Preset User Menu, hold the SET (7) button

for 3 seconds. The curser will blink. Select from

Preset or User with the UP (4) or DOWN (5) buttons. After finishing the edit hold the SET (7) button until the curser stops blinking.

or

To turn OFF, Press the POWER SWITCH (2) for 3 seconds and release. The receiver will turn off.

Refer to the System Operation instructions, Scan Function, (pg. 17) to select operating frequency.

RECEIVER SETUP MENUS

Control Menus have two modes, Preset and User.

To make changes Hold the SET (7) button for 2 seconds and use the UP (4) DOWN (5) buttons. To save changes hold the SET (7) button for 3 seconds. The UP (4) or DOWN (5) buttons control volume when not in SET mode.

OPERATING INSTRUCTIONS

U-1000,U-2000 Receiver

Powering the Receiver

Plug the AC-DC ADAPTOR provided in the 15 VDC INPUT JACK (17) on the back of the receiver. Then plug the adapter into an AC outlet. (Note: Any 15V DC source with 800 mA capability can also be used.) Connect either the XLR balanced or 1/4” unbalanced output to your mixing board, effects, or amplifier. To turn ON, Press the POWER SWITCH (2) for 1 second. The LCD DISPLAY

(3) will flash the company and model number. Then the channel assignment RF LEVEL METER, and the AUDIO LEVEL METER will display when the transmitter is activated.

SPECIFICATIONS

SYSTEM SPECIFICATIONS

Operating Frequency Range	....................1000 channels switchable
Freq. Synthesized	PLL system with frequency stability <0.005%
Frequency Response	30 HZ-15 KHZ ±3 dB
Dynamic Range	120 dB
Harmonic Distortions	<0.5%
Modulation	FM ±25 KHz nominal
Operating Range	250 feet typical (depending on site
	conditions) up to 500+ feet optimum
	line of sight

RECEIVER SPECIFICATIONS

Receiving System	Dual conversion superheterodyne
	with True Diversity (2 complete receiver
	sections with optimum audio selected)
Sensitivity	-107 dBm, nominal
Selectivity	60 dB nominal ± 75 KHz offset
Image Rejection	-70 dB, minimum
Spurious Rejection	65 dB, nominal
Mute Threshold	-65 dBm to -100 dBm Adjustable
Audio Output Level	Unbalanced output: 360 mV Adjustable
Mic Level Balanced Output	24 mV Adjustable
Audio Output Impedance	Balanced and unbalanced: both 600 ohms
Controls	Power On/Off switch, Level control,
	UP or DOWN Channel select buttons,
	Mute (RF squelch) adjust
LCD Display	Single backlit LCD panel indicating
	channel/frequency selected, received
	AF and RF level, and A/B diversity status
USB Port	U-1000, U-2000 (connecting cord supplied)
Power Requirements	115 VAC or 240 VAC, external
	AC-DC adaptor
Antenna	Right angle or external remote
Dimensions	U-1000/2000 19” full rack x 1 RU
	19” x 11.75” x 1.75” [W / D / H]
	(49 cm x 30 cm x 4.5 cm)
Weight (power supply included)	U-1000 113 oz. (49.5 Kg.)
	U-2000 120 oz. (52.5 Kg.)

TRANSMITTER SPECIFICATIONS

Models Available	UH-1000 handheld mic, UB-1000 bodypack
RF Output Power	1 mW-50 mW max
	(country and band dependent)
Harmonic and Spurious Emissions	- 50 dB
Audio Input Level	UH-1000: 24 mV RMS (nom.)
	UB-1000: 225 mV (Instr.), 150 mV (HM),
	75 mV (Lav)

20