CARE OF GLASS AND PLATED PARTS

If the glass is not kept clean permanent discolouration and / or blemishes may result. Normally a hot fire will clean the glass. The most common reasons for dirty glass in- clude: not using sufficient fuel to get the stove thoroughly hot, using green or wet wood, closing the draft so far that there is insufficient air for complete combustion. If it is necessary to clean the glass, use a soft cloth with a non- abrasive cleaner. DO NOT CLEAN THE GLASS WHEN HOT!

The glass is very strong but do not let burning fuel rest or fall against it and always close the door gently. NEVER FORCE IT SHUT! If the glass should ever crack while the fire is burning, do not open the door until the fire is out and do not operate the stove again until the glass has been replaced with a new 5mm thick piece of ceramic glass, available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. To remove the door, open and lift out; remove the screws and brackets holding the glass in place. Remove all broken glass. Wrap the edges of the new glass with a U-shaped strip of fiberglass gasket, covering 1/4" on each side. Place this gasketed glass in position and replace the brackets and screws. When finished, you should be able to move the glass slightly, horizontally and vertically.

Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth.

Prolonged high temperature burning with the door ajar may cause a permanent rainbowing effect on the lower edge of a gold plated door.

HI-EFFICIENCY HEATING

FOUR OPTIONS

For a basic hi-efficiency fireplace, blowers are not needed, however, they are recommended for extra heat output and efficient air circulation. This can be especially important if the fireplace is to be used as a major source of heat. Without the use of blowers, the Napoleon Model NZ25 will operate as a regular hi-efficiency fireplace.

A BLOWER KIT (NZ62) may be purchased with the option of adding up to one additional blower. These blowers are installed in the rear of the unit and are used to direct the heat into the room where the fireplace is located. The blow- ers are controlled, by a variable speed switch, located inside the fireplace.

A THERMOSTATIC AIR CONTROL (NZ690KT), may

be used for constant heat, complete with automatic damper and thermostat, wall mounted in the room containing the fireplace, and at least 10 feet (minimum) from the fire- place. This option allows your room temperature to be kept as evenly controlled as it would with other fuels while still enjoying the comfort of wood heat.

THE HOT AIR GRAVITY VENT SYSTEM (NZ220)5

may be used to distribute heat to an adjoining room (lo- cated either above, or beside the room containing the fire- place) by way of vents, eliminating the need of an addi- tional blower. While this system may be used in conjunc- tion with the optional blowers, it could reduce the flow of hot air being distributed to additional rooms. It must be experimented with and the dampers adjusted manually to suit your requirements. This may take a few attempts; thereafter adjustments should no longer be required as is normally experienced with your central heating system registers. The hot air vent must be installed in an up- ward direction! NEVER install in a downward direction. Figures 4c, 4d & 4e. The hot air gravity vent system is not be connected to a central heating system (for this application use the NZ62CH). No more than two hot air gravity vents can be installed to fireplace. Individual vent runs are not to exceed 10 feet.

All hot air gravity vents must be insulated.

A CENTRAL HEATING SYSTEM (NZ62CH) may be

used to heat rooms up to 50 feet from the unit. A wall mounted thermostat located in the room to be heated con- trols the blower supplying warm air from the room con- taining the fireplace. If a hot air duct system exists, the central heat blower may safely be tied into this system to reduce the amount of new ducting required. Consult with a heating specialist to ensure a proper duct layout for your home.

FIGURES3

WS-415-71 /09.07.00

Page 4 Page 6
Page 5
Image 5
Napoleon Fireplaces NZ25 manual Care of Glass and Plated Parts, Four Options
Page 4 Page 6

NZ25 specifications

The Napoleon Fireplaces NZ25 is a standout option for those looking to enhance their living space with an elegant and efficient heating solution. This stylish fireplace embodies the perfect blend of cutting-edge technology, aesthetic appeal, and practical functionality.

One of the key features of the NZ25 is its impressive heating capacity. Designed for medium to large living areas, the fireplace is capable of producing a remarkable 20,000 BTUs (British Thermal Units) per hour. This potent output makes it an ideal choice for homeowners seeking to maintain a comfortable atmosphere during colder months.

The NZ25 is built with innovative heating technologies that prioritize efficiency. The fireplace utilizes a high-efficiency design, ensuring that a greater portion of the fuel is converted into heat rather than lost through the chimney. As a result, it not only heats your space more effectively but also reduces fuel consumption, making it an eco-friendly option for conscientious consumers.

Moreover, the NZ25 features Napoleon’s Advanced Airflow System, which ensures optimized heat distribution throughout the room. This technology enhances the fireplace's heating capabilities, allowing for consistent warmth and comfort, regardless of where you're seated in the room. Paired with an array of customizable settings, users can effortlessly control the flame and heat output to suit their specific preferences.

The aesthetic appeal of the NZ25 is another highlight. It offers an attractive contemporary design that complements various interior styles, making it a beautiful focal point in any living area. The fireplace can be customized with an assortment of decorative media, which allows homeowners to personalize the look and feel of their space.

Safety is also a top priority with the NZ25. It features a robust safety screen and has been designed to minimize the risk of accidents. With Napoleon’s commitment to quality, the NZ25 is built to last, ensuring that it remains a reliable heating source for years to come.

In summary, the Napoleon Fireplaces NZ25 combines an impressive heating output with modern efficiency technologies and appealing design. Whether for warmth or aesthetics, this fireplace represents an excellent investment for any home.
Top Page Image Contents