Smart Internet Phone Adapter | 2. THEN, INSTALL THE TA612V VOICE ADAPTER | |
a. Plug the power cable into the Power port on the TA612V Smart Internet | ||
TA612V | ||
Phone Adaptor and into an electrical outlet. This turns on your Smart | ||
| Internet Phone Adaptor. You do not need to unplug it when not in use. |
3. SET UP AN ACCOUNT AT BBPGLOBAL |
a) Power up the computer. |
b) Use a Web browser to go to the bbpglobal web site, |
http://www.bbpglobal.com/netgear/ |
Follow the instructions to setup your account. During this process, |
BBPGlobal
Add voice to your internet
www.bbpglobal.com
INSTALLATION GUIDE
INSTALLATION WITH MULTIPLE DEVICES
This guide shows you how to set up your Smart Internet Phone Adaptor with a Router or Switch instead of just a single PC. This way you can share your internet connection with multiple computers (i.e. via Wireless Lan).
1. SET UP THE NETWORK CONNECTIONS |
a. Unplug the power cable for your modem. |
b. Unplug the power cable for your router. |
c. Disconnect the Ethernet cable connectiong your modem to your |
router from the WAN/Internet port on your router, and connect |
that end of the Ethernet cable to the Internet port on the TA612V |
Smart Internet Phone Adaptor. |
d. Connect one end of the Ethernet cable we provide into the PC |
port on the TA612V. Connect the other end of this Ethernet cable |
into the WAN/Internet port on your router. |
12VDC, 1.2A |
|
| Restore | PC | Internet |
Phone 2 | Phone 1 | Factory |
|
| |
Power | Settings |
|
| ||
(inactive) |
|
|
| ||
|
|
|
|
|
b.Check that the Power light
on the Smart Internet Phone Adaptor is illuminated. Wait at least five minutes for the phone adapter to start up. There may be updates that need to be downloaded such as new firmware or changes to your features. Do not interrupt the registration process by unplugging the power or lifting the receiver on your phone during the
c.The status light on the front of the TA612V will flash. Wait two minutes before continuing.
d.Plug the power cable back into your router and wait about two minutes for it to start up before continuing.
e.Connect a telephone to the TA612V Phone 1 port using the adapter provided.
f.If you have a DSL modem that requires PPPoE you need to set up your PPPoE username and password in the TA612V. Point your browser to: http://192.168.61.1/
Log in using the username and password printed on the back of the TA612V. After setup reboot your TA612V.
Blink=Activity | Ethernet: Green=100Mbps/Amber=10Mbps |
you will be asked to provide your contact information, the serial |
number and the MAC address of your TA612V, shown at the back |
of your unit. |
c) Reboot your TA612V after registration. |
d) After reboot, pick up your telephone handset and listen for a dial |
tone. If you hear dial tone then you have finished installation and |
may begin making calls. For dialing instructions, see the Helpfule |
Hints on this card. If you do not hear a dial tone, see |
Troubleshooting. For more tips about troubleshooting, see the |
User Manual. |
e) (Optional) You may also select a PSTN number to receive phone |
calls. Please go to the following web site to select a PSTN number. |
Please note there is an additional charge for this service. |
http://www.bbpglobal.com/phonenumber/ |
TROUBLESHOOTING
If you have no dial tone, check the following:
•Make sure the phone is plugged into the proper port on the Smart Internet Phone Adaptor (phone port #1)
•Make sure the Internet light 
on the Smart Internet Phone Adaptor is active. If not, check your connection to the Internet. Try rebooting your modem. If that does not work, contact your internet provider’s customer service.
BBPGlobal
Add voice to your internet
e. Plug the power cable back into your modem. Wait about two |
minutes for it to start up. |
Internet
Phone 2
Phone 1
The easiest way to get VoIP
Power
Status
PC
www.bbpglobal.com
