Never use wood or plastic, it may break and block the parts.
Never spray any cleaning product on the emitter grid or burner area.
6.Troubleshooting
Problem |
| Possible Cause | What to do |
| |||||
|
|
|
| ||||||
|
|
| Purge gas line by holding | ||||||
| Air in gas line | control | knob | at | “PILOT” | ||||
| position for at least two | ||||||||
|
|
| |||||||
|
|
| minutes. |
|
|
|
|
| |
Burner won’t light | Blockage in orifice | Clean orifice |
|
|
|
| |||
|
|
|
|
|
|
|
| ||
| Gas pressure is low | Replace cylinder |
|
|
| ||||
|
|
|
| ||||||
|
|
| Use match to light pilot | ||||||
| Igniter is not sparking | through the hole at the base of | |||||||
|
|
| heater head. |
|
|
|
| ||
| Thermocouple is not operating | Replace thermocouple |
| ||||||
| properly |
|
|
|
|
|
| ||
| Dirt build up around pilot orifice | Clean pilot orifice |
|
| |||||
|
|
|
| ||||||
|
|
| Check connections at hose to | ||||||
| There may be a leak in the system | fuel line and fuel line to heater | |||||||
Pilot won’t stay lit | that | has been detected by the | head. | Be | sure | Regulator | |||
| safety system in the regulator. | hand wheel is tightened to | |||||||
|
|
| cylinder valve properly. |
| |||||
|
|
| Put heater in more protected | ||||||
| High | wind condition blowing out | location. | use | heater | in | winds: | ||
| pilot flame | Do not | |||||||
| greater than 10 miles/hr. or | ||||||||
|
|
| |||||||
|
|
| temperature: below 40 F. | ||||||
| Heater not leveled | Level the heater |
|
|
| ||||
|
|
|
|
| |||||
| The burner tilted | Straighten burner |
|
| |||||
|
|
|
|
|
| ||||
| Gas pressure is low | Replace cylinder |
|
|
| ||||
Emitter glows uneven |
|
|
|
|
|
|
|
| |
Outdoor temperature is below 40 | Refill the cylinder. Using full | ||||||||
| |||||||||
| degrees Fahrenheit and cylinder is | one. |
|
|
|
|
| ||
| less than 20% full | Stop using this heater when | |||||||
|
|
| the temperature is below 40 F. | ||||||
| The burner burn off oily materials | During the first few minutes of | |||||||
| the initial burning |
|
|
| |||||
Burner emits smoke |
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |||
| Blockage in burner | Remove | blockage | and | clean | ||||
| burner inside & outside |
| |||||||
|
|
|
| ||||||
|
|
|
|
|
|
| |||
| The base is not on a level surface | Place heater | on | a | level | ||||
| surface |
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||
|
|
|
| ||||||
Carbon build up | Dirt or film on dome and emitter | Clean dome and emitter |
| ||||||
|
|
|
|
|
|
|
| ||
|
|
| Remove | blockage | and | clean | |||
| Blockage in burner | burner and clean burner inside | |||||||
|
|
| & outside. |
|
|
|
|
13