PART |
|
| R0805A | |||||
Key |
|
| Key |
|
| Key |
|
|
No. Qty. | Description | No. Qty. | Description | No. Qty. | Description | |||
1 | 1 | Base | 42 | 4 | Crank Bushing | 84 | 6 | M8 x 23mm Button |
2 | 1 | Frame | 43 | 2 | Crank Bushing Sleeve |
|
| Screw |
3 | 1 | Upright | 44 | 2 | Crank Bearing Set | 85 | 1 | M6 x 10mm Button |
4 | 1 | Console Bracket | 45 | 1 | Crank |
|
| Screw |
5 | 1 | Console | 46 | 1 | Crank Spacer | 86 | 2 | Crank Screw |
6 | 1 | Front Stabilizer | 47 | 2 | Crank Snap Ring | 87 | 8 | Hub Screw |
7 | 1 | Rear Stabilizer | 48 | 1 | Upper Wire Harness | 88 | 10 | M8 Washer |
8 | 1 | Left Handlebar | 49 | 1 | Lower Wire Harness | 89 | 2 | M10 x 60mm Button |
9 | 1 | Right Handlebar | 50 | 1 | Reed Switch/Wire |
|
| Screw |
10 | 2 | Handlebar Endcap | 51 | 1 | Belt | 90 | 3 | M8 Split Washer |
11 | 1 | Left Upper Body Arm | 52 | 1 | Flywheel | 91 | 1 | Flywheel Spacer |
12 | 1 | Right Upper Body Arm | 53 | 1 | “C” Magnet | 92 | 1 | Flywheel Washer |
13 | 1 | Left Pedal | 54 | 1 | Pillow Block | 93 | 1 | Flywheel Snap Ring |
14 | 1 | Left Pedal Leg | 55 | 1 | Magnet | 94 | 4 | Pillow Block Screw |
15 | 1 | Right Pedal | 56 | 1 | Spring | 95 | 1 | Stop Screw |
16 | 1 | Right Pedal Leg | 57 | 1 | Idler | 96 | 1 | M8 x 35mm Screw |
17 | 2 | Upright Cover | 58 | 1 | Idler Bracket | 97 | 1 | “E” Clip |
18 | 1 | Left Front Handlebar | 59 | 1 | Clamp | 98 | 4 | Pulley Screw |
|
| Cover | 60 | 1 | Reed Switch Bracket | 99 | 2 | Crank Washer |
19 | 1 | Left Rear Handlebar | 61 | 1 | Base Pin | 100 | 2 | M4 x 25mm Screw |
|
| Cover | 62 | 2 | Latch Bracket Spacer | 101 | 8 | M4 x 16mm Round |
20 | 1 | Right Front Handlebar | 63 | 2 | Hair Pin |
|
| Head Screw |
|
| Cover | 64 | 1 | Latch Bracket | 102 | 4 | Motor Washer |
21 | 1 | Right Rear Handlebar | 65 | 1 | Pivot Bracket | 103 | 27 | M4 x 16mm Screw |
|
| Cover | 66 | 2 | Pivot Bracket Spacer | 104 | 8 | M4 x 14mm Screw |
22 | 1 | Water Bottle Holder | 67 | 1 | Frame Pin | 105 | 6 | M4 x 32mm Round |
23 | 2 | Front Stabilizer Endcap | 68 | 1 | Latch Button |
|
| Head Screw |
24 | 2 | Rear Stabilizer Endcap | 69 | 1 | Roll Pin | 106 | 2 | M8 x 31mm Shoulder |
25 | 2 | Wheel | 70 | 1 | Motor |
|
| Screw |
26 | 1 | Base Foot | 71 | 1 | Resistance Cable Pulley | 107 | 4 | M4 x 12mm Screw |
27 | 2 | Leveling Foot | 72 | 1 | Resistance Cable Set | 108 | 2 | M4 x 45mm Screw |
28 | 1 | Left Side Shield | 73 | 2 | Foam Grip | 109 | 2 | Large Wave Washer |
29 | 1 | Right Side Shield | 74 | 1 | Pivot Axle | 110 | 2 | M8 Small Washer |
30 | 6 | Upper Body Bushing | 75 | 2 | Hub Cover | 111 | 2 | Wave Washer |
31 | 4 | Pedal Leg Cover | 76 | 2 | Outer Crank Cover | 112 | 8 | Star Washer |
32 | 2 | Pedal Leg Axle | 77 | 4 | M6 x 20mm Button | 113 | 1 | M10 Washer |
33 | 4 | Pedal Leg Bushing |
|
| Screw | 114 | 1 | M6 Nut |
34 | 1 | Base Axle | 78 | 4 | M8 x 43mm Button Bolt | 115 | 4 | M8 x 23mm Shoulder |
35 | 2 | Base Bushing | 79 | 7 | M8 Jamnut |
|
| Screw |
36 | 2 | Crank Arm | 80 | 1 | M8 x 69mm Button Bolt | # | 2 | Allen Wrench |
37 | 2 | Inner Crank Cover | 81 | 4 | M10 Nylon Locknut | # | 1 | Grease |
38 | 2 | Crank Hub | 82 | 2 | M10 x 80mm Carriage | # | 1 | User’s Manual |
39 | 1 | Pulley Spacer |
|
| Bolt |
|
|
|
40 | 1 | Pulley | 83 | 2 | M10 x 127mm Button |
|
|
|
41 | 2 | Crank Bushing Cover |
|
| Screw |
|
|
|
Note: “#” indicates a
25
