9. Apply grease to the welded bolt on the Left Pedal Arm | 9 |
|
| Wide | Narrow | ||
(3). Slide a Chrome Tube (21) and a Chrome Tube |
|
| |||||
|
|
| Side |
| Side | ||
Washer (84) onto the welded bolt. Make sure that the |
|
|
|
| |||
|
|
| 4 |
|
|
| |
Chrome Tube is turned exactly as shown in the |
|
|
|
|
|
|
|
inset drawing. Then, tighten an M10 Nylon Locknut | Lubricate |
|
|
|
|
| |
(26) onto the welded bolt. |
|
|
| 26 | 84 | 21 | 3 |
|
|
| 21 |
|
|
| |
Attach the other Chrome Tube (not shown) to the Right |
|
| Grease |
|
|
| |
Pedal Arm (4) in the same way. |
|
|
|
|
| ||
|
|
| 3 |
|
|
| |
|
|
|
|
|
|
| |
Apply a small amount of the included Teflon¨ lubricant |
|
|
|
|
|
|
|
to a paper towel. Rub a thin film of the lubricant onto | 84 |
|
|
|
|
|
|
both Chrome Tubes (21). | 26 |
| Welded Bolt |
|
|
| |
|
|
|
|
| |||
|
|
|
|
|
| ||
10. Slide the Left Upper Body Arm (7), which is marked | 10 |
|
|
|
|
|
|
with an ÒLÓ sticker, onto the Chrome Tube (21) on the |
|
|
|
|
|
| |
|
|
|
|
|
| 75 | |
Left Pedal Arm (3). Slide the Right Upper Body Arm |
|
|
|
|
|
| |
(75) onto the Chrome Tube on the Right Pedal Arm (4). |
|
|
|
|
|
|
|
Make sure that the Upper Body Arms are on the |
|
|
|
|
|
|
|
correct sidesÑthe upper ends should bend in the |
|
|
|
|
|
|
|
direction shown by the arrows. Next, slide an Axle |
|
|
| 74 |
|
| |
Cover (74) onto the post on each Upper Body Arm. |
|
|
|
|
|
|
|
Apply grease to the Arm Axle (19). Insert the Arm Axle |
|
|
| 19 |
|
| 34 |
|
|
| 74 |
| 15 | ||
into the Upright (2), the right Pivot Cover (74), and the | 7 |
|
|
| |||
|
|
|
|
|
| ||
Right Upper Body Arm (75) as shown. Push the Arm |
|
|
|
|
|
| |
|
|
|
|
| 2 |
| |
Axle into the Upright until the left end of the Axle is flush |
|
|
|
|
|
| |
|
|
| Grease |
|
|
| |
with the left side of the Upright. Next, raise the Left |
|
|
|
|
|
| |
Upper Body Arm (7) and insert the Arm Axle into the |
|
|
| Post |
|
|
|
left Axle Cover (74) and the Left Upper Body Arm. |
| 15 |
|
|
|
|
|
Center the Arm Axle. | 34 |
|
|
|
| 21 | |
Using the included pedal tool, tap two Push Nuts (15) |
|
|
|
|
|
| 4 |
|
|
|
|
|
|
| |
about 1/8Ó onto each end of the Arm Axle (19). Make |
|
|
|
|
|
|
|
sure that the Push Nuts are turned as shown in the |
|
|
| 21 |
|
|
|
inset drawing. Note: It may be helpful if another person |
|
|
|
|
|
|
|
holds a block of wood against one end of the Arm Axle | Pedal Tool | 15 | 19 |
|
|
| |
while you tap Push Nuts onto the other end. |
|
|
| ||||
Press the two Axle Caps (34) onto the Arm Axle (19). |
|
|
| 3 |
|
|
|
|
|
|
|
|
|
| |
11. Plug the Power Supply (78) into the jack at the rear of | 11 |
|
|
|
|
|
|
the elliptical crosstrainer. Note: Your Power Supply |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
may look different from the one pictured. |
|
|
|
|
|
|
|
|
|
|
| Jack |
|
|
|
|
|
|
|
| 78 |
|
|
12.Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical crosstrainer.
8
