HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged.
Plug in the power cord (see |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
page 13). Next, locate the |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
reset/off circuit breaker on |
| Reset | |||||
|
|
|
|
|
| ||
the treadmill frame near the |
| Position |
|
|
|
|
|
|
|
|
|
|
| ||
power cord. Switch the cir- |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
cuit breaker to the reset po- |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
sition. |
|
|
|
|
|
|
|
IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the displays light as soon as you plug in the power cord and switch the circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays remain lit, see THE INFORMATION MODE on page 23 to turn off the demo mode.
Next, stand on the foot |
| |
rails of the treadmill. |
| |
Find the clip attached to | Clip | |
the key (see the drawing |
| |
to the right) and slide | Key | |
the clip onto the waist- | ||
| ||
band of your clothes. |
|
Then, insert the key into
the console. After a moment, the displays will light. IM-
PORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully tak- ing a few steps backward; if the key is not pulled from the console, adjust the position of the clip.
Note: If there is a sheet of clear plastic on the face of the console, remove the plastic. To prevent dam- age to the walking platform, wear clean athletic shoes while using the treadmill. The first time you use the treadmill, observe the alignment of the walking belt, and center the walking belt if neces- sary (see page 27).
Note: The console can display speed and distance in either miles or kilometers. To find out which unit of measurement is selected or to change the unit of mea- surement, see THE INFORMATION MODE on page
23.For simplicity, all instructions in this section refer to miles.
HOW TO USE THE MANUAL MODE
1 Insert the key into the console.
See HOW TO TURN ON THE POWER to the left.
2 Select the manual mode.
Each time the key is inserted, the manual mode will be selected. If you have selected a program, press any of the program buttons (Event Training, Aerobic Fitness, Performance, Custom, Heart Rate Control, or Weight Loss) repeatedly until a track and the word “Manual” appears on the screen.
3 Start the walking belt and adjust the speed.
To start the walking belt, press the Start button, the Speed increase button, or one of the num- bered speed (MPH) buttons.
If the Start button or the Speed increase button is pressed, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed in- crease and decrease buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if you keep your finger on the button, the speed setting will change in increments of 0.5 mph. If one of the numbered speed (MPH) buttons is pressed, the walking belt will gradually increase in speed until it reaches the selected speed set- ting.
To stop the walking belt, press the Stop button. To restart the walking belt, press the Start button, the Speed increase button, or one of the numbered speed (MPH) buttons.
4 Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the Incline increase and decrease buttons or one of the numbered incline (% GRADE) buttons.
Each time the Incline increase or decrease button is pressed, the incline will change by 0.5%. If one of the numbered incline (% GRADE) buttons is pressed, the incline will gradually increase until it reaches the selected incline setting.
15
