3. With the help of a second person, carefully raise the | 3 |
|
|
|
|
Frame (7) to the storage position and make sure that the |
| 7 |
|
| |
|
|
|
| ||
lock pin is properly engaged as described on page 25. |
|
|
|
| |
|
|
|
|
| |
Position the Base Plate (115) on the treadmill as shown. |
|
|
|
|
|
Attach the Base Plate with the three Base Plate Screws |
| 114 |
|
| |
(114). Note: It may be helpful if a second person tips the |
|
|
| ||
|
|
|
|
| |
treadmill slightly as you tighten the Screws. |
|
|
|
|
|
Carefully lower the Frame (7) to the floor as described on |
|
|
|
|
|
page 25. |
|
|
|
|
|
|
| 115 |
|
|
|
4. Place one of the Handrail Spacers (92) on the right | 4 |
|
| A |
|
Upright (83) as shown, with the cutout on the indicated |
|
|
| ||
| 79 |
| Cutout | ||
side (see inset drawing A). Pull the Upright Wire Harness |
|
| |||
|
|
| |||
(131) up through the cutout. Place the other Handrail |
|
|
|
|
|
Spacer on the left Upright (not shown). |
|
|
| 92 |
|
|
|
| 73 |
| |
Have a second person hold the Handrails (73) near the |
|
|
|
| |
|
|
|
|
| |
Uprights (83) as shown. Connect the Upright Wire |
|
|
| B |
|
Harness (131) to the wires extending from the right |
| 131 | 83 | 131 | |
Handrail. Insert the connectors and the Upright Wire |
|
|
|
| |
|
|
|
|
| |
Harness (131) into the opening in the Console Base (79) |
|
|
|
|
|
(see inset drawing B). |
|
|
|
|
|
Set the Handrails (73) on the Handrail Spacers (92), |
| 92 |
|
|
|
|
|
|
|
| |
being careful not to pinch the Wire Harness (131). |
|
|
|
| 79 |
5. Insert two Handrail Bushings (94) into the right Upright | 5 |
|
|
|
|
(83). Turn the Handrail Bushings so they fit against the |
|
|
|
| |
|
|
|
|
| |
Upright as shown in the inset drawing. |
|
|
| 73 |
|
|
|
|
|
| |
Insert two Handrail Bolts (96) with Handrail Washers |
|
| 92 |
| |
(95) into the Handrail Bushings (94), the right Upright |
|
|
| ||
|
|
| 83 |
| |
(83), and the right Handrail Spacer (92). Lift up the right |
|
|
|
| |
Handrail (73) and align the Bolts with the holes in the |
|
|
| 94 | |
Handrail. Next, thread the Bolts into the Handrail. Do |
|
|
|
| 95 |
not tighten the Bolts yet. |
|
|
|
| |
|
|
|
|
| |
Attach the left Handrail (not shown) in the same way. |
|
|
|
|
|
Tighten all four Handrail Bolts (96). |
| 94 |
|
|
|
|
| 95 |
| 96 | |
6.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or carpet from damage, place a mat under the treadmill.
7
