Part |
|
| Rev. 1098A | |||
To find the parts listed below, refer to the | Exploded Drawing | attached in the center of this owner’s guide. | ||||
Key No. Qty. | Description |
| Key No. Qty. | Description | ||
1 | 2 | Rear Roller Adj. Bolt |
| 51 | 4 | Plastic |
2 | 1 | Front Roller Adj. Bolt |
| 52 | 1 | Wire Harness |
3 | 2 | Rear Roller Guard |
| 53 | 2 | Rear Pad |
4 | 1 | On/Off Switch |
| 54 | 1 | Left Rear Endcap |
5 | 1 | Storage Latch |
| 55 | 1 | Sensor Star Washer |
6 | 4 | Isolator |
| 56 | 4 | Frame Pivot Bolt |
7 | 2 | Ground Wire Screw |
| 57 | 1 | Console Wire Harness |
8 | 6 | Platform Screw |
| 58 | 1 | Right Foot Rail |
9 | 1 | Left Foot Rail |
| 59 | 1 | Motor Bolt |
10 | 4 | Handrail Endcap |
| 60 | 1 | Sensor Bracket Nut |
11 | 1 | Reed Switch Clip |
| 61 | 2 | Sensor Locknut |
12 | 4 | Wire Clip |
| 62 | 18 | Belly Pan Fastener |
13 | 1 | Choke |
| 63 | 1 | Right Rear Endcap |
14 | 4 | Small Plug |
| 64 | 2 | Base Endcap |
15 | 1 | Key/Clip |
| 65 | 1 | Releaseable Wire Tie |
16 | 1 | Frame |
| 66 | 5 | 8” Wire Tie |
17 | 1 | Front Roller/Pulley |
| 67 | 1 | Wire Tie Holder |
18 | 1 | Rear Roller |
| 68 | 2 | Frame Endcap |
19 | 1 | Incline Frame |
| 69 | 1 | Incline Disk |
20 | 1 | Electronics Shield |
| 70 | 1 | Upright/Base |
21 | 1 | Incline Motor Shield |
| 71 | 1 | Motor |
22 | 2 | Pivot Spacer |
| 72 | 1 | Pulley/Flywheel/Fan |
23 | 2 | Side Hood Bracket |
| 73 | 1 | Latch Catch |
24 | 8 | Wheel Nut |
| 74 | 1 | Reed Switch/Sensor Wire |
25 | 6 | Incline Bolt/Motor Tension Bolt | 75 | 2 | Wheel Spacer | |
26 | 1 | Incline Motor |
| 76 | 1 | Photo Switch |
27 | 1 | Controller |
| 77 | 1 | 8” Ground Wire |
28 | 1 | Electronics Plate |
| 78 | 1 | Console |
29 | 2 | Rear Isolator |
| 79 | 1 | Shock |
30 | 2 | Wheel |
| 80 | 1 | Walking Belt |
31 | 1 | Power Cord |
| 81 | 1 | Walking Platform |
32 | 1 | Power Cord Grommet |
| 82 | 1 | Incline Stop Bracket |
33 | 1 | Front Hood Bracket |
| 83 | 1 | Latch Warning Decal |
34 | 1 | Outlet Bracket |
| 84 | 1 | Motor Hood |
35 | 1 | Circuit Breaker |
| 85 | 1 | Incline Motor Plate |
36 | 4 | Rear Platform Screw |
| 86 | 4 | Hood Screw |
37 | 2 | Wheel Bolt |
| 87 | 1 | Allen Wrench |
38 | 1 | Front Belly Pan |
| 88 | 1 | Wrench Clip |
39 | 1 | Motor Pivot Bolt |
| 89 | 6 | Base Pad |
40 | 1 | Motor Pivot Nut |
| 90 | 30 | Small Screw |
41* | 1 | Motor/Pulley/Flywheel/Fan |
| 91 | 4 | Pad Screw |
42 | 1 | Motor Belt |
| 92 | 1 | Power Supply |
43 | 29 | Screw |
| 93 | 2 | Latch Spacer |
44 | 2 | Endcap Plate |
| 94 | 2 | Foot Rail Track |
45 | 1 | Motor Tension Washer |
| 95 | 1 | Magnet |
46 | 2 | Tension Star Washer |
| 96 | 2 | Motor Tension Nut |
47 | 2 | Sensor Screw |
| 97 | 2 | Incline Warning Decal |
48 | 2 | Belt Guide |
| 98 | 1 | Front Roller Adj. Nut |
49 | 3 | Roller Adjustment Washer |
| 99 | 2 | Warning Decal |
50 | 1 | Belly Pan |
|
|
|
|
22
