Return |
to Menu |
T7406 Cordless Telephone
User Card
BDisplay
CDisplay buttons
GFeature
FRelease
N
Antenna
Collar light | A |
|
Memory and | D |
line buttons | |
Handset Card | E |
Hold H |
|
Installation: First-time battery charging
WARNING: The rechargeable battery pack must be fully charged before you use your T7406 handset for the first time.
To correctly charge a new battery pack and handset:
1. Charge the battery pack in the bat- |
tery port at the back of the charger for a |
minimum of 30 minutes. |
2. Install the battery pack onto the back |
of the handset. |
3. Put the handset into the handset port |
on the charger. When the contacts |
touch correctly, the handset charge |
indicator (left LED) lights up red. The |
battery pack is fully charged when the |
Telephone setup continued
Security code (continued)
4.Press CHANGE to assign a security code to the handset. The display shows Enter Password.
5.Enter the
6.Press OK. The display shows Press 6 digits
7.Enter the
8.Press OK to accept the code.
The display shows 4. Set S.S. Code :
If you are assigning a handset to an existing base, your handset is now connected to the system.
If you are assigning the first handset to a new base station (which has no security code), continue with the following
© 2002 Nortel Networks
P0942259 03
Printed in Taiwan
Headset port | 1 | 2 ABC | 3 DEF |
| |||
| 4 GHI | 5 JKL | 6 MNO |
| 7 PQRS | 8 TUV | 9 WXYZ |
M |
| 0 | # |
|
|
| |
Lanyard |
|
|
|
anchor |
|
| J |
|
|
| |
Volume |
| Microphone | |
I |
|
| |
control |
| Options | |
L | Dialpad |
| |
| button/Mute | ||
|
| ||
KO
Battery
Pack
LED turns green (three hours). |
4. Place the spare pack into the back |
battery port. The battery pack indicator light (right LED) turns red while it charges. The spare battery pack is fully charged in approximately 12 hours (LED turns green).
Telephone setup
Each handset must be registered to a base by sharing an identi- cal security code. A base can support up to three independent handsets. Each handset assigned to a base station must have a unique Set ID (1, 2 or 3).
When viewing the back of the base station, the
steps:
9.When the displays shows 4. Set S.S. Code :, press NEXT to get ready to send the security code to the base.
The display shows 5. Send S.S. Code.
10.Unplug the AC power adapter connected to the base, and plug it back in again.
11.Within 15 seconds, press and hold the OK for five sec- onds to send the security code to the base. The display shows Send OK! and you hear a beep when the transfer is successful.
Note: If the Security Code transfer fails, Send Error! dis- plays. To correct this, repeat steps 10 and 11.
12.Press the Options button. The date and time displays.
Handset options
To access the following handset options:
Your T7406 cordless telephone
AAntenna collar light
Flashes to signify an incoming call.
BDisplay
Shows the time and date, call information, handset status icons, and guides you through features and options menus.
CDisplay buttons
The labels for display buttons appear on the second line of the display. Display button functions change with each feature.
Options Lists=7 | Feature message |
SHOW QUIT | Display button label |
| Display icons |
| Display button |
Your T7406 cordless telephone
F® Release button
Ends an active call.
G≤ Feature button
Starts or cancels a feature.
H≥ Hold button
Places calls on hold.
IDialpad
JMicrophone
KOptions button/Mute
Answers calls, mutes the microphone on an active call, and accesses the Options list on the display.
LVolume control
Adjusts the handset, headset, and ringer volume.
Handset ID #
For each new handset, you must first configure the handset ID # to identify the handset to the base station:
1.Press the Options button.
2.Press SHOW.
3.Press NEXT until the display shows 6. Handset ID.
4.Press SHOW. The display shows the current Handset ID.
5.If you want to change the ID number, press CHANGE. The display shows Enter Password.
6.Enter the
7.Press OK. The display shows Press Digit
8.Press the appropriate digit on the dialpad.
9.Press OK to accept the configuration.
Refer to the Installation manual for instructions about how to change the password.
Security code
If your installer has already set up a base, obtain the security code and follow steps 1 to 8, inclusive.
1.Press the Options button.
2.Press SHOW.The display shows 1. Ring Type.
3.Press NEXT until the display shows you the selection.
4.Follow the directions in each section.
5.Press QUIT to exit the menu.
Ring type
To select a ring type for your handset:
1.When the display shows 1. Ring Type, press SHOW.
2.Press CHANGE to listen to the different types of ring. Note: There is also a Ringer Off setting.
3.Press OK to accept the ring type of your choice. The display shows the ring type number you chose.
Volume level
To select the ringer volume level for your handset:
1. | Press NEXT until the display shows 2. Ringer Volume. |
2. | Press SHOW. The display shows Press Volume bar. |
3. | Press the volume bar on the left side of the handset to |
| adjust the ringer volume. |
4. | Press OK to accept the ringer volume. |
DMemory and line buttons
These buttons provide
EHandset card
Write the button function on this card.
MLanyard anchor
For attaching a wrist strap.
NHeadset port
For connecting a headset.
OBattery pack
If you need to assign a security code to the base, follow all the steps in this section.
To assign a security code to a handset follow steps 1 to 8:
1.Press the Options button.
2.Press SHOW.
3.Press NEXT until the display shows 4. Set S.S. Code :.
Continued...
The display shows 2. Ringer Volume. |
Lock Handset
To lock the buttons on the handset to prevent unintentional button presses:
1.Press NEXT until the display shows 3. Lock Handset.
2.Press OK. The display shows Handset Locked.
3.To release the handset, press ®, then press •.
