Manuals / North Star / Lawn and Garden / Log Splitter

North Star M1108D owner manual Splitting Operation, Extend wedge, Split Control Lever Operation

Models: M1108D

1 45

Download 45 pages 3.13 Kb

Page 24

6.Extend wedge

Splitting Operation

6.Extend wedge

7. Stop wedge

8.Important

STUCK LOG procedure

Move Split Control Lever toward endplate to extend wedge and split log.

SPLIT CONTROL LEVER OPERATION

Important safety instructions:

•Operator position. ALWAYS operate the log splitter from the manufacturer’s indicated OPERATOR POSITION. (See diagram above.) Other positions are unsafe because they can increase the risk of injury from crushing, cutting, flying objects, or burns.

•Remove hands. Remove both hands from log before activating Split Control Lever.

•Hand activate. Use only your hand to operate the Split Control Lever. Never use any other body part, or a rope, cable, or other remote device to actuate the control.

•Second person. Many accidents occur when there is more than one person involved in loading and operating the log splitter. Only one person should operate the controls. If a second person is assisting in loading logs, the operator must NEVER actuate the Split Control Lever until the assistant and all bystanders are at least 10 feet away. NEVER allow an assistant to hold the log in place while the operator actuates the Split Control Lever.

Release Split Control Lever to stop wedge movement when log is split.

WARNING: Cracks in logs can close quickly and pinch fingers. Keep fingers away from any cracks that open in partially split logs.

SPLIT CONTROL LEVER OPERATION

If a log does not split completely and becomes stuck on the wedge, follow the instructions below to remove the log.

A log can become stuck to the wedge if the wedge becomes embedded in the log and the log doesn’t split and separate. This can happen if the log is too stringy or tough to split completely. A stuck log will move back with the wedge on the initial attempt to retract the wedge. If this happens, retract the wedge completely to allow the splitter to strip the log from the wedge. Keep hands clear of log and wedge while wedge is retracting.

24

Image 24

North Star M1108D owner manual Splitting Operation, Extend wedge, Split Control Lever Operation, Stop wedge 8. Important

Contents

Instructions for Assembly, Testing, Operation, Servicing Storage Any Questions, Comments, Problems or Parts OrdersREAD and UNDERSTAND this manual completely before using log splitter M1108DHazard Signal Word Definitions Table of Contents About Your Log Splitter Attention All Rental Companies and Private Owners who loanthis equipment to others Warranty RegistrationSafety Label Locations order new labels or unsafe operation could resultSafety Label Locations SPLIT CONTROL LEVER OPERATIONHORIZONTAL VERTICALMachine Component Identification DescriptionDescription Initial Set-Up Step One Inspect Log Splitter Components Step Two Add Oil to EngineStep Three Add Hydraulic Oil to Reservoir Closely inspect all log splitter componentsInitial Set-Up Step Four Lubricate KeepersBEAM WEDGE KEEPEROptional 4-Way Wedge Wings Moving and Towing to the Job Site Moving the log splitterIMPORTANT Make sure log splitter engine is off 1. Place in Horizontal position 2. Engine off4. Attach safety chains Review towing safety instructions in your vehicle manualAttach safety chains Moving and Towing to the Job SiteImportant safety instructions Moving and Towing to the Job Site7. Lock front outrigger leg down & unhitch Tow log splitter carefully to desired work siteBefore Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each use2. Remove debris 3. Fuel tank / lines 4. Mechanical parts Remove debris from engine, muffler, and moving partsBefore Each Use-Inspection / Maintenance follow spark arrestor manufacturer’s service instructions5. Hydraulic system Check the hydraulic system carefully before removing hydraulic oil dipstickBefore Each Use-Inspection / Maintenance 9. Tires 10. Shields / guardsReplace all guards and shields after servicing the log splitter Before Each Use - Fueling Important Safety InstructionsClean up fuel spills /splashes immediately Step Two FuelingBefore Each Use - Work Site Selection & Set-Up 2. Fire precautionsTake the following precautions against fire Step Three Work site selection and log splitter set-upBefore Each Use - Work Site Selection & Set-Up 4. Lock both outrigger legs DOWN 5. Block wheels 6. Apply greaseLock both the outrigger legs in the “DOWN” position Block the wheels to prevent unintended movement of the log splitterSplitting Operation General safety informationWear the following protective clothing and safety gear Splitting Operation3. Set to horizontal3 Lock in vertical position using catch pin through the vertical lock Splitting Operationb Set to VerticalImportant safety instructions Splitting Operation5. Load log Correct Log OrientationImportant safety instructions Release Split Control Lever to stop wedge movement when log is splitSplitting Operation 6. Extend wedgeSplitting Operation 9. Return wedgeMove Split Control Lever away from end plate to return wedge SPLIT CONTROL LEVER OPERATIONStorage WARNING A hot engine can be a fire hazard1. Retract wedge 2. Cool 3. Wipe with oily rag 4. Engine manual 5. Splitter storage location 6. Gasoline storagePeriodic Maintenance maintenanceEngine As specified in enginePeriodic Maintenance 8. Extend and retract wedge 5 five times to purge air from the system9. Check hydraulic oil level and fill if necessary Troubleshooting Any Questions, Comments, Problems or Parts OrdersImportant Safety Instructions Specifications Parts Breakdown - Exploded View 1108, 1109, 1114 - Rev D Parts Breakdown - Exploded View 1108, 1109, 1114 - Rev D Summary of Important Safety Information for Operation Safety in Moving and Towing the Log SplitterGeneral safety while Moving Safety During TowingSummary of Important Safety Information for Operation Safety - Before Use Read/instructSafety During Inspection/Maintenance Personal protective equipmentSummary of Important Safety Information for Operation Safety During FuelingSafety in Work Site Selection Summary of Important Safety Information for Operation Safety - During Use General Safety During UseSafety in Loading, Operating, and Unloading Loading/UnloadingSummary of Important Safety Information for Operation Safety - After useAssembly Instructions Closely inspect all log splitter componentsBeam Return Line Vertical Beam LockHorizontal Beam Lock Swivel FittingAssembly Instructions Step Assembly InstructionsStep StepAssembly Instructions StepStep StepStep 9a Assembly InstructionsStep StepStep 9b Step 11aAssembly Instructions StepStep 11b Assembly InstructionsStep StepAssembly Instructions StepStep Step