Manuals / North Star / Lawn and Garden / Log Splitter

North Star M1108D Step, Assembly Instructions, Tighten Bolts to 90 lb-ft with a wrench

Models: M1108D

1 45

Download 45 pages 3.13 Kb

Page 40

Image 40

Assembly Instructions

Step 1

Remove shipping crate

If there are rubber boots on the axles, remove and discard them

Slide Wheel onto Axle with Valve Stem facing out

Slide Outer Bearing onto Axle (outer bearing may be shipped loose in parts bag or loose inside wheel)

Outer bearing taper points into log splitter Slide Wheel Washer onto Axle

Axle with the

Outer Rubber Boot

Bearingremoved

Wheel

Washer

Axle Nut

Wheel

Cotter
	Valve Stem Out
Pin

Step 2

Thread Axle Nut onto Axle (hand tight) Back Axle Nut off ¼ turn

Make sure Wheel spins freely

Insert Cotter Pin through hole in Axle and bend it so Axle Nut cannot come off

Make sure Wheel spins freely

Tap Dust Cap onto Wheel with a soft faced mallet

Repeat steps 1 and 2 for the other Wheel

Step 3

Connect Towbar to Axle/Tank using (2) Tank Bolts and (2) Tank nuts (already in place)

Tighten Bolts to 90 lb-ft with a wrench

Wheel

Axle Nut

Dust Cap

Cotter Pin

Bolt

Axle/Tank

Towbar

Fig 02417

Page 40

Image 40

North Star M1108D owner manual Step, Assembly Instructions, Tighten Bolts to 90 lb-ft with a wrench

Contents

Instructions for Assembly, Testing, Operation, Servicing Storage Any Questions, Comments, Problems or Parts OrdersREAD and UNDERSTAND this manual completely before using log splitter M1108DHazard Signal Word Definitions Table of Contents About Your Log Splitter Attention All Rental Companies and Private Owners who loanthis equipment to others Warranty RegistrationSafety Label Locations order new labels or unsafe operation could resultSafety Label Locations SPLIT CONTROL LEVER OPERATIONHORIZONTAL VERTICALDescription Machine Component IdentificationDescription Initial Set-Up Step One Inspect Log Splitter Components Step Two Add Oil to EngineStep Three Add Hydraulic Oil to Reservoir Closely inspect all log splitter componentsInitial Set-Up Step Four Lubricate KeepersBEAM WEDGE KEEPEROptional 4-Way Wedge Wings Moving and Towing to the Job Site Moving the log splitterIMPORTANT Make sure log splitter engine is off 1. Place in Horizontal position 2. Engine off4. Attach safety chains Review towing safety instructions in your vehicle manualAttach safety chains Moving and Towing to the Job SiteImportant safety instructions Moving and Towing to the Job Site7. Lock front outrigger leg down & unhitch Tow log splitter carefully to desired work siteBefore Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each use2. Remove debris 3. Fuel tank / lines 4. Mechanical parts Remove debris from engine, muffler, and moving partsBefore Each Use-Inspection / Maintenance follow spark arrestor manufacturer’s service instructions5. Hydraulic system Check the hydraulic system carefully before removing hydraulic oil dipstick9. Tires 10. Shields / guards Before Each Use-Inspection / MaintenanceReplace all guards and shields after servicing the log splitter Before Each Use - Fueling Important Safety InstructionsClean up fuel spills /splashes immediately Step Two FuelingBefore Each Use - Work Site Selection & Set-Up 2. Fire precautionsTake the following precautions against fire Step Three Work site selection and log splitter set-upBefore Each Use - Work Site Selection & Set-Up 4. Lock both outrigger legs DOWN 5. Block wheels 6. Apply greaseLock both the outrigger legs in the “DOWN” position Block the wheels to prevent unintended movement of the log splitterSplitting Operation General safety informationWear the following protective clothing and safety gear Splitting Operation3. Set to horizontal3 Lock in vertical position using catch pin through the vertical lock Splitting Operationb Set to VerticalImportant safety instructions Splitting Operation5. Load log Correct Log OrientationImportant safety instructions Release Split Control Lever to stop wedge movement when log is splitSplitting Operation 6. Extend wedgeSplitting Operation 9. Return wedgeMove Split Control Lever away from end plate to return wedge SPLIT CONTROL LEVER OPERATIONStorage WARNING A hot engine can be a fire hazard1. Retract wedge 2. Cool 3. Wipe with oily rag 4. Engine manual 5. Splitter storage location 6. Gasoline storagePeriodic Maintenance maintenanceEngine As specified in engine8. Extend and retract wedge 5 five times to purge air from the system Periodic Maintenance9. Check hydraulic oil level and fill if necessary Any Questions, Comments, Problems or Parts Orders TroubleshootingImportant Safety Instructions Specifications Parts Breakdown - Exploded View 1108, 1109, 1114 - Rev D Parts Breakdown - Exploded View 1108, 1109, 1114 - Rev D Summary of Important Safety Information for Operation Safety in Moving and Towing the Log SplitterGeneral safety while Moving Safety During TowingSummary of Important Safety Information for Operation Safety - Before Use Read/instructSafety During Inspection/Maintenance Personal protective equipmentSafety During Fueling Summary of Important Safety Information for OperationSafety in Work Site Selection Summary of Important Safety Information for Operation Safety - During Use General Safety During UseSafety in Loading, Operating, and Unloading Loading/UnloadingSummary of Important Safety Information for Operation Safety - After useAssembly Instructions Closely inspect all log splitter componentsBeam Return Line Vertical Beam LockHorizontal Beam Lock Swivel FittingAssembly Instructions Step Assembly InstructionsStep StepAssembly Instructions StepStep StepStep 9a Assembly InstructionsStep StepStep 9b Step 11aAssembly Instructions StepStep 11b Assembly InstructionsStep StepAssembly Instructions StepStep Step