DM3001X
MIXER FEATURES
INPUTS
1.Input faders - control individual source levels in the mix.
2.Input Toggle Switch (Transform) - selects which source will be live to that channel based on what you have connected to the rear panel input section. By removing the face panel the switch can be rotated into any of eight positions.
3.
4.Channel EQ – adjusts the Treble, Middle, and Bass frequencies respectively of the channel audio. Full rotation to the left creates a “CUT” effect eliminating most of the sound from that frequency area.
MICROPHONE
5.Mic Gain Controls – controls the DJ Mic volume for the Neutrik™ “Combo” connector on the front panel.
6.Treble and Bass Controls – for
7.¼” input connector - allows connection of a 1/4” microphone jack directly into the mixer.
HEADPHONE CUEING
8.Channel PFL/Cue Assign - are used to route Pre Fader Level (PFL) channel audio to the Monitor Section. The channel faders do not control the Cue volume.
9.PFL Meter Indicator – lights when PFL audio is not being sent to the LED meter. When the LED is off the channel audio the sent to the meter display for PFL matching. Accurately match channel levels with the
10.Headphone Mix - controls the mix of PFL and PGM signals to your headphones. When the slider is moved to the left, all you will hear is the cue source. When the slider is all the way to the right, you will hear what is playing through the master output. By blending, beats can be matched exactly and segues can be smooth when a song is cued.
11.Headphone Level – adjusts cue volume.
12.Split/Blend Cue – controls how PFL and Program audio are sent to your headphones. In split mode, the PFL audio can be heard in your left ear and PGM audio can be heard in your right ear. In blend mode, both PFL and PGM can be heard in both ears.
13.Headphone output – for your 1/4” or 1/8” headphones.
OUTPUTS
14.Master Fader – controls the overall output level.
15.Stereo Auto Peak Hold Level Indicator- quickly and accurately tracks level of audio output. The red LEDs show output overload. When using as a master output meter, set the crossover, equalizer and power amp inputs to avoid distortion at each step in the audio chain. Will also act as PFL meter when PFL/Cue buttons are pressed.
16.Zone Output - controls output zone level for monitors or extra sound system.
CROSSFADER
17.Crossfader - achieves clean segues between the two input channels selected by the Crossfader Assign.
18.Crossfader Slope – determines how quickly the audio from the opposing side of the crossfader activates. A tight curve (right position) turns on the opposing audio signal with very little crossfader movement. A loose curve (left position) makes very long and smooth segues in transition.
19.Hamster switch with Off position – reverses the direction of the crossfader. In the center position the crossfader is deactivated.
20.Crossfader Assign – channels 1 or 2 can be assigned to the left. Channels 2 and 3 can be assigned to the right. If for example channels 1 and 3 were selected then "Hard left" selects Channel 1 and "Hard right" selects Channel 3. With the crossfader centered, both assigned channels are live. Use the crossfader for fast and seamless segues from one selected channel to the other.
Note: If channel 2 is selected on both sides, the crossfader will turn off channel 2 in the left position and turn it on in the right position
Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large screws that hold it in place, lift it out and disconnect its cable.
21.Beat Lights – Indicate when strong bass beats are present to allow more accurate beat mixes.
22.Push Button transforms – By pressing these button the crossfader channel will respond as determined by the transform assign
23.KILL switches - By moving these toggle down or up the marked frequency area will be removed. For instance is BASS is pressed the bass beat will be removed, Highs might remove cymbals, and middle might remove vocals.
OTHER ITEMS
24.Power Switch – Actives mixer power. Always turn on input devices first, the mixer second, and amplifiers last!
25.Light Connector – for attaching a 12V BNC style gooseneck light.
- The Leader in DJ Technology
©2001 | Industries | - 7 - | http://www.numark.com |
