NuTone warranty Typical Installations, Plan the Installation, Model 761WHNT

MODEL 761WHNT

Page 

DECORATIVE ventilation fan with light

READ AND SAVE THESE INSTRUCTIONS

WARNING

TYPICAL INSTALLATIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.	Use this unit only in the manner intended by the manufacturer.
	If you have questions, contact the manufacturer at the address
	or telephone number listed in the warranty.
2.	Before servicing or cleaning unit, switch power off at service
	panel and lock the service disconnecting means to prevent
	power from being switched on accidentally. When the service
	disconnecting means cannot be locked, securely fasten
	a prominent warning device, such as a tag, to the service

POWER CABLE
	MOUNTING TABS
CEILING
JOIST
	HOUSING
CEILING	GRILLE
	PAN
MATERIAL
	GLASS
	LIGHT SHADE

POWER CABLE	ADDITIONAL
MOUNTING	FRAMING	*
TABS
2 x 4		2 x 4
CEILING	CEILING
JOIST or	JOIST or
TRUSS	TRUSS
HOUSING
CEILING	GRILLE
	PAN
MATERIAL
	GLASS

LIGHT SHADE

	panel.
3.	Installation work and electrical wiring must be done by a
	qualified person(s) in accordance with all applicable codes
	and standards, including fire-rated construction codes and
	standards.
4.	Sufficient air is needed for proper combustion and exhausting
	of gases through the flue (chimney) of fuel burning equip-
	ment to prevent backdrafting. Follow the heating equipment
	manufacturer’s guideline and safety standards such as those
	published by the National Fire Protection Association (NFPA),
	and the American Society for Heating, Refrigeration and Air
	Conditioning Engineers (ASHRAE), and the local code authori-
	ties.
5.	When cutting or drilling into wall or ceiling, do not damage
	electrical wiring and other hidden utilities.
6.	Ducted fans must always be vented to the outdoors.
7.	NEVER place a switch where it can be reached from a tub or
	shower.
8.	This unit must be grounded.
9.	This unit is U.L. listed. Type I.C. inherently protected.

CAUTION !

1. For general ventilating use only. Do not use to exhaust hazard-

Housing mounted			Housing mounted
directly to joist				to 2x4 truss
2x6 (or larger)			Requires additional framing
Discharge parallel to joists.			for mounting tabs.
			Discharge parallel to joists.
POWER CABLE	ADDITIONAL
		FRAMING *
MOUNTING
	TABS
			4" ROUND
			DUCT		POWER
					CABLE
HOUSING					MOUNTING
				HOUSING
"I"					TAB
		"I"
JOIST CEILING
MATERIAL		JOIST
		GRILLE			GRILLE
			SUSPENDED
GLASS LIGHT SHADE		PAN			PAN
			CEILING		GLASS
Housing mounted to “I” joist			MATERIAL
					LIGHT SHADE
Requires additional framing			SUSPENDED CEILINGS
for mounting tabs.
			Housing hung with wires -
Discharge parallel to joists.
			3-point mount.

*Additional framing must be a 2x6 (minimum height), at least 9-inches long.

PLAN THE INSTALLATION

	ous or explosive materials and vapors.
2.	This product is designed for installation in FLAT CEILINGS
	ONLY. Do not mount this product in a wall.
3.	The light fixture assembly must be mounted to the fan housing
	assembly included with this product. Do not mount the light
	fixture assembly to a wiring outlet box.
4.	To avoid motor bearing damage and noisy and/or unbalanced
	impellers, keep drywall spray, construction dust, etc. off power
	unit.
5.	Please read specification label on product for further informa-
	tion and requirements.

Installer:

Leave this manual with the homeowner.

Homeowner:

Use and Care information on page 4.

The unit will operate most quietly and efficiently when located where the shortest possible duct run and minimum number of elbows will be needed.

Use a roof cap or wall cap that has a built-in damper to reduce backdrafts.

Plan to supply the unit with proper line voltage and appropriate power cable.

insulation

(Can be placed around and over fan housing.)

fan
housing 4-in.
	ROUND
* Purchase	DUCT	*
		4-in. ROUND
separately		ELBOW(S) *	WALL CAP *