Attach Rudder to Kayak

1.Lubricate the nylon sleeve with soapy water and insert it in the top of the rudder mount (7).

2.Place a small wooden block over the end of the sleeve (to avoid damage), and hammer it into place. The sleeve must go at least halfway into the rudder mount. Excess sleeve can be cut off.

3.Remove the ring from the end of the pin on the rudder assembly. Pull the pin out of the rudder housing--don’t lose the white washers.

4.Insert the pin through the nylon sleeve to attach it to the mount. Make sure to place the white washers between the rudder housing and the kayak on both ends of the pin.

5.Replace the ring in the end of the pin once the rudder assembly is mounted.

Attach Steering Lines to Rudder

1.At the stern of the kayak, put the end of each steering line down through the top of the shoulder washer in the middle hole on each side of the rudder steering plate.

2.Hold the rudder still with the blade centered within the housing. Pull each steering line equally tight through

the middle hole. (Which hole you use is not critical, although it will effect rudder responsiveness.)

3.Loop the steering lines through the holes and finish off as shown. By pulling the bungie tight, the steering line can be inserted into the same hole as the bungie and no knots will be required to keep the line in place.

4.Trim the excess line, leaving at least 3 inches below the steering plate. (You can now remove the tape from the steering slides.)

Install Rudder Retraction Line

1.The rudder retraction line should go through the center of the rudder housing. Continue pulling the line up toward the seat and through the loop in the hatch/gear straps along the right side of the kayak to keep the line out of the way.

2.Place the clam cleat at the rear of the seat on the right side of the kayak, as indicated by two small “v” marks in the plastic. Make sure the cleat is facing forward (the “c” shape should face the bow). Attach the clam cleat with 2 self-tapping screws.

3.Place the standard strap eye 1 inch in front of the clam cleat, as indicated by two more small “v” marks, and secure it with the other two self-tapping screws.

4.Run the line through the strap eye. Pull the line so there is no slack, but not so tightly that the rudder rises. Tie the line to the strap eye.

5.The rudder can now be raised by pushing the line away from the side of the kayak (just behind the clam cleat). Insert the tight line into the clam cleat to hold the rudder up. To lower the rudder, pull the line out of the clam cleat.

Page 2 Page 4
Page 3
Image 3
Ocean Kayak 14561 manual Attach Rudder to Kayak, Attach Steering Lines to Rudder, Install Rudder Retraction Line
Page 2 Page 4

14561 specifications

The Ocean Kayak 14561 is a versatile and robust sit-on-top kayak designed for recreational paddlers who seek an enjoyable experience on the water. This kayak is an embodiment of innovation, merging comfort, stability, and performance in a captivating design.

One of the defining features of the Ocean Kayak 14561 is its spacious design, providing ample room for both the paddler and gear. With a length of 14 feet and a width of approximately 30 inches, this kayak offers impressive stability, making it suitable for various water conditions, from tranquil lakes to mild ocean waves. The kayak's generous hull design enhances its tracking efficiency, allowing smooth navigation even in choppy waters.

The Ocean Kayak 14561 is equipped with several key technologies aimed at improving the paddler's experience. The Comfort Plus seat back is designed for extended paddling sessions, offering customizable support and enhanced comfort. Additionally, the kayak features adjustable footrests, allowing paddlers of different heights to find their ideal position, which aids in efficient paddling.

Storage is crucial for any kayak, and the Ocean Kayak 14561 does not disappoint. It includes both a rear tank well and a forward storage hatch, allowing users to secure items safely while enjoying their time on the water. This makes it a great choice for day trips, fishing expeditions, or leisurely paddling adventures.

Another notable characteristic of this kayak is its polyethylene construction, which is both lightweight and durable. This material choice not only adds to the kayak's longevity but also makes it relatively easy to transport and maneuver, whether you’re loading it onto a vehicle or launching it from the beach.

The kayak features built-in grab handles, making it easier to carry and stabilize during transport. This attention to detail reflects Ocean Kayak’s commitment to user-friendly design.

Overall, the Ocean Kayak 14561 stands out as a high-quality choice for paddlers seeking stability, comfort, and versatility. Its combination of practical features and thoughtful technologies ensures an enjoyable and hassle-free paddling experience, making it ideal for enthusiasts looking to explore a variety of aquatic environments. Whether you are a novice just starting or a seasoned paddler, the Ocean Kayak 14561 caters to all skill levels, ensuring that everyone can experience the joys of kayaking.
Top Page Image Contents