Fig. M
JOINING THE BALL SHAFT
AND CLAMP ASSEMBLY

 

 

 

 

 

 

OPTION IV:

 

STEP 2:

 

 

 

 

 

 

For Wood Speakers with NO Threaded Inserts

 

POSITIONING CLAMP ASSEMBLY

 

 

 

 

 

 

 

Place the speaker on a scratch-proof surface. Be careful to

 

Ceiling or Floor Mounting

 

 

 

 

 

protect any exposed components from damage. Position the

 

The Wall Mount Ball Shaft may also be used

 

 

 

mounting plate at the chosen location on the speaker. Using the

 

 

mounting plate as a template, with a pencil, mark the outline

 

to mount a speaker from the ceiling. For

 

 

 

of the two slots on the surface of the speaker.

 

installation placement, see Fig. I-2.

 

 

 

 

 

 

 

CAUTION: Be careful not to drill or screw into a speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

where you could possibly damage internal components.

 

 

 

 

 

 

 

 

 

 

If there’s a question about this, check with your dealer or

 

 

 

 

 

 

 

 

 

 

the manufacturer, or you may choose to carefully remove

 

 

 

 

 

 

 

 

 

 

the driver and check inside the speaker enclosure

 

 

 

 

 

yourself.

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP 3:

ATTACHING CLAMP ASSEMBLY

Insert the two anchors fully until the flange is flush against the

mounting surface (Fig. J & K).

Position the clamp assembly over

the anchors.

Insert and tighten the #12 coarse thread screws (provided). (Fig L). Use a Phillips screwdriver or a Phillips bit in a battery powered

drive tool (Fig. M).

STEP 4:

Caution: Tightest is not always the best! Over tightening fasteners can weaken the installation. Make sure the

connection is extremely solid and then stop tightening.

If the speaker angle must be changed, do not attempt to move the speaker without first loosening the tension screw. Reposi- tion, then tighten the tension screw further until the speaker is held firmly in place.

If rotational adjustment of the mounted speaker is required, the jam nut must first be loosened, the speaker rotated, and the jam nut tightened again. Use the 7/16” (11mm) open wrench or a small adjustable crescent wrench for this procedure.

Caution: If the speaker loses its position, do not attempt to move the speaker without first loosening the tension screw.

Reposition, then tighten the tension screw further until

Remove the mounting plate from the speaker where you had been using

it as a template. Insert the 3/32” drill Fig. F bit (provided) so that ½” sticks out

of the end of your drill.

Position the drill bit ¼” down from

the far end of the slot but centered in the middle of the slot.

Drill the pilot hole straight down into speaker. Repeat the procedure for the second slot location. (Fig. F).

Place mounting plate onto the speaker,

insert the #14 screws and tighten until the Fig. G screws are firmly seated against the top

of the mounting plate.

Do not overtighten! (Fig. G).

Using the 7/16 open wrench or small crescent wrench, tighten the jam nut securely against the top of the mounting plate (Fig. H).

Fig. H

STEP 2:

POSITIONING CLAMP ASSEMBLY

Wall Mounting

Position the clamp plate vertically the OmniMount Logo should be facing toward the ceiling, the tension screw head faces towards the floor (Fig. I).

The clamp assembly should be positioned so

 

that the clamp plate (with the OmniMount

 

logo) faces in the same direction as the front

 

of the speaker you are mounting. The jaw

 

and the tension screw will face in the

 

opposite direction (towards the wall) (fig O).

 

Position the clamp assembly onto the wall,

 

ceiling or floor at the mounting location you

Fig. I-2

have selected.

 

STEP 3:

ATTACHING CLAMP ASSEMBLY

Using the clamp plate as a template, mark the two holes with a pencil. Remove the clamp plate before drilling into your mounting surface.

CAUTION: It may be necessary to check that the surface prepara- tion and the fasteners will not interfere with electrical wiring, plumbing, etc., behind the mounting surface (wall, ceiling, or floor).

Your OmniMount Speaker Mount is designed to be mounted on a variety of wall and ceiling constructions. Please follow all safety precautions listed here before installing the Clamp and Jaw Assembly.

CAUTION: Drilling holes into masonry or concrete material requires the use of a carbide tipped 5/16” (8mm) diameter masonry drill and/or hammer drill. Always wear eye protection.

Mounting Onto Solid Wood or Masonry

Insert a 5/16” (8mm) diameter drill bit (not provided). Set depth of drill at a minimum 2 1/2” (63.5mm) protruding from the end of your drill.

Center the drill on the marked hole locations and carefully drill the two holes to the minimum 2 ½” (63.5mm) depth.

Check that the clamp assembly is open enough to accept the ball. Get the 5/32” (4 mm) hex wrench. Now lift the speaker into position and “pop” the ball into the clamp assembly. Set your chosen angle of adjustment.

While supporting the speaker, insert the long end of the hex key and turn the hex tension screw clock-wise to take up the slack in the clamp assembly, but do not fully tighten. (The ball should be

properly seated, and the speaker should

Fig. N

still move easily). (Fig. N).

 

ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING

THE CLAMP ASSEMBLY

Orient and hold the speaker in its final fixed position.

CAUTION: The weight of the speaker must be fully supported throughout the entire tightening process. Do not allow the ball shaft to rest upon or push against the clamp assembly. Two installers may be needed for this; one to support the speaker while the other tightens the clamp assembly.

Insert the hex key into the tension screw head

and tighten (Fig. O)

Pick up the vice grip pliers, regular pliers,

or small crescents wrench and use one of these

Fig. O

tools to assist in tightening the tension screw.

Tighten in ½ turn increments until the speaker is

 

firmly held in place.

 

NOTE: To hold the speaker in position and

 

prevent any slippage, the clamp assembly must

 

get a good “bite” into the ball and form a

 

SOLID joint. The clamp assembly needs to be

 

tightened enough to lock and hold the speaker

 

FIRMLY at the chosen angle. When that point

 

is reached, no further tightening is necessary.

 

the speaker is held firmly in place.

CONGRATULATIONS!

YOUR INSTALLATION IS NOW COMPLETE.

Note: The following is made in lieu of all warranties expressed or implied. The Manufacturer’s only obligation shall be to replace parts of this product proved to be defective within two years of the date of purchase. We are aware that this mounting assembly may be used for purposes and in ways other than those for which it had been designed and manufactured. The Manufac- turer, Distributor, Retail and their respective agents cannot be held responsible or liable for injuries or property damage— direct, indirect, or consequential—arising out of the use, or inability to use this product safely and properly.

Note: Every effort has been made to provide accurate and error- free assembly and installation information. Omnimount Systems disclaims liability for any difficulties arising from the interpreta- tion of information contained in these instructions.

Omnimount Systems, Inc.

8201 South 48th Street

Phoenix, AZ 85044-5355

Voice: 480-829-8000

Fax: 480-756-9000

Email: hdqrs@omnimount.com

Web: www.omnimount.com

Copyright 2002, Omnimount Systems, Inc. All rights reserved. OmniMount products are covered by patents issued and/or pending. “OmniMount” is a registered trademark of Omnimount Systems, Inc.

OmniMount products are manufactured in the USA. Printed In the USA.

20.0 speaker mount kit Rev 03/02

Fig. I

Fig. J

Fig. K

Fig. L

Page 2
Image 2
Omnimount 20.0 Option Step, Step Attaching Clamp Assembly, Step Positioning Clamp Assembly, Congratulations

20.0 specifications

Omnimount 20.0 is an innovative mounting solution that has garnered significant attention for its advanced features, cutting-edge technologies, and user-friendly characteristics. Designed to enhance the way users interact with their audiovisual equipment, Omnimount 20.0 aims to deliver unmatched flexibility and robust performance whether at home, in educational institutions, or within corporate environments.

One of the standout features of Omnimount 20.0 is its versatile mounting options. The system supports a wide range of devices, from televisions to projectors, ensuring compatibility with various display sizes and weights. This adaptability makes it an ideal choice for any space, whether it’s a small living room or a large conference hall.

The technology behind Omnimount 20.0 is also noteworthy. The solution incorporates advanced tilt and swivel capabilities, allowing for optimal viewing angles without the hassle of manual adjustments. This feature is particularly beneficial in environments where multiple viewers are present, as it helps to minimize glare and enhance the overall viewing experience. Additionally, the quick-release mechanism simplifies installation and maintenance, giving users the convenience of easily accessing their devices for upgrades or repairs.

Durability and build quality are key characteristics of Omnimount 20.0. Constructed from high-grade materials, this mounting solution is engineered to withstand the test of time. It is designed to securely hold heavier devices, providing peace of mind to users concerned about stability and safety. The sleek, modern design seamlessly complements contemporary spaces, making it not just functional but also visually appealing.

Another significant aspect of Omnimount 20.0 is its ease of installation. Accompanied by detailed instructions and all necessary hardware, the mounting solution can be set up quickly, even by those with limited technical skills. The intuitive mounting bracket system eliminates guesswork, ensuring that users can confidently install their equipment.

In conclusion, Omnimount 20.0 represents a remarkable advancement in the realm of mounting solutions. With its versatile compatibility, innovative technologies, robust design, and user-friendly characteristics, it stands as a top choice for anyone looking to enhance their audiovisual experience. Whether for personal or professional use, Omnimount 20.0 delivers on its promise of quality and convenience, making it a must-have product in today’s tech-savvy world.