CCH-1
ID | Description | Qty |
|
|
|
1 | Shelf | 1 |
|
|
|
2 | Shelf Pegs | 2 |
|
|
|
3 | Foot Assembly | 2 |
|
|
|
4 | Leg Assembly | 2 |
|
|
|
5 | Extended Leg | 2 |
|
|
|
6 | Spacer | 2 |
|
|
|
7 | Lock Nut | 2 |
|
|
|
8 | Support Screw | 2 |
|
|
|
9 | Hex Wrench | 1 |
|
|
|
10 | Rubber Pad | 4 |
|
|
|
The
Installing on CRT TV
First, determine your chassis style:
Fig. 1 | Fig. 2 |
|
| Fig. 3 |
|
Thread Foot Assemblies (3) into Spacers (6). (Fig. 3) |
|
|
Attach Foot Assemblies to position 2 on Shelf with Support Screws (8). | Fig. 4 | |
(Fig 4) |
|
|
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly (3) and front edge of Shelf. (Fig. 5)
Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 5) |
|
Fig. 5 |
|
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of TV, as |
|
shown in Fig. 6. |
|
Thread Foot Assembly In or Out of Spacer until Shelf sits level. |
|
Note: Maximum foot extension is shown in Fig 6. | Fig. 6 |
Tighten Lock Nut (7) against leg to hold level position. | |
Proceed to section titled Mounting Components to |
|
|
| |
Extend Leg from Leg Assembly (4) using Hex Wrench (9). Thread Foot Assem- |
| |
bly (3) into Leg Assembly(4). (Fig 7). | Fig. 8 | |
Attach Leg Assemblies to position 2 on Shelf with Support Screws (8). (Fig 8) | ||
| ||
Fig. 7 |
|
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly and front edge of Shelf. (Fig. 9)
Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 9) |
| |
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of TV, as shown in Fig. 10. | Fig. 9 | |
|
| |
| Loosen hex screw and slide Leg In or Out until Shelf sits level, then |
|
| secure Leg in position with hex wrench. |
|
| Note: Maximum extension is shown in Fig 10. |
|
| For additional minor adjustments, thread Foot Assembly In or Out of |
|
Fig. 10 | Leg until Shelf sits level. Tighten Lock Nut (7) against leg to hold |
|
level position. |
| |
|
|
Proceed to section titled Mounting Components to
Installing on DLP/LCD Projection TV
First, determine your chassis style:
Fig. 11 | Fig. 12 |
|
C—Shallow Back
Extend Leg from Leg Assembly (4) using Hex Wrench (9). Thread
Foot Assembly (3) into Leg Assembly(4). (Fig 13).
Fig. 14
Attach Leg Assemblies to position 1 on Shelf with Support Screws
(8). (Fig 14)
Fig. 13
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly and front edge of Shelf. Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 15)
Fig. 15
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of
TV, as shown in Fig. 16.
Loosen hex screw and slide Leg In or Out until Shelf sits level, then secure Leg in position with hex wrench.
| Note: Maximum extension is shown in Fig 16. |
| For additional minor adjustments, thread Foot Assembly In or Out of Leg until Shelf sits |
| level. Tighten Lock Nut (7) against leg to hold level position. |
Fig. 16 | Proceed to section titled Mounting Components to |
|
D—Steep Back
Remove Leg from Leg Assembly (4) using Hex Wrench (9). Install Ex- tended Leg (5) into Leg Assembly (4) using Hex Wrench (9). Thread Foot Assembly (3) into Leg Assembly(4). (Fig 17).
Fig. 18
Attach Leg Assemblies to position 1 on Shelf with Support Screws (8). (Fig 18)
Fig. 17
2 | 3 |