One for All URC 6800 manual Using the Sleep KEY, Trouble Shooting, Problem Solution

USING THE SLEEP KEY

The SLEEP key allows you to access the sleep timer of your TV, Cable Converter/DBS Satellite or Audio component. You can access your TV, Cable Converter, DBS Satellite or Audio component’s Sleep Timer by pressing the SLEEP key. Most Sleep Timers advance in increments of 10 or 15 minutes, however, for specific instructions on setting your components Sleep Timer, please consult your original owner’s manual.

Even if your original Cable Converter remote control did not have a sleep timer, your Cinema 6+ has its own built-in sleep timer.If your Cable Converter does not have a sleep timer, pressthe SLEEP key to activate the Cinema 6+’s built-in sleep timer. For example:

1. Press and release the CBL/SAT key then press the SLEEP key once to set the Cinema 6+’s built-in sleep timer for 15 minutes. The red light will blink once.

2.Each additional press of the SLEEP key will add 15 more minutes to the Sleep Timer, up to a maximum of 60 minutes. The LED will blink twice when the sleep timer is set for 30 minutes, 3 times for 45 min- utes, or 4 times for 60 minutes.

NOTE:The sleep timer starts 10 seconds after

the last press of the SLEEP key. Once you have activated the Cinema 6+’s built-in sleep timer, you must keep the remote control aimed directly at the component.

3.To de-activate the built-in sleep timer,press POWER.

NOTE: Plugging your TV into the outlet on the back of the Cable Converter may allow you to turn both your Cable Converter and TV ON and OFF.

Web Site : http://www.oneforall.com

TROUBLE SHOOTING
Problem	Solution
Red light does not	Replace the batteries with four (4) new AAA alka-
blink when you press	line batteries.
a key?
The Cinema 6 does	Try all of the codes listed for your brand of home
not operate your	entertainment component in the “Setup Codes” sec-
home entertainment	tion. Many setup codes may allow for partial func-
components or is not	tionality, however, only one setup code will operate
performing com-	your home entertainment component correctly.
mands properly?	Make sure that all of the components you are
	setting up can be operated with an infrared
	remote control.
Problems program-	Try the VCR set-up codes for your brand. However,
ming a TV/VCR	some combo units may require both a TV code for
combo?	volume control and a VCR code for the remaining
	functions.
VCR not recording?	As a safety feature on the Cinema 6, you must
	press the REC key twice.
CH▲ / ▲and PREV	Due to RCA design (1983-1987), only the original
CH not working for	remote control will operate these functions.
your RCA TV?
Problems changing	If your original remote control required an Enter
channels?	keystroke when changing channels, press the
	ENTER key on the Cinema 6 after you enter the
	channel number.
The red light blinks	Make sure you are aiming your Cinema 6 at your
when you press a	home entertainment component and that you are
key but you receive	within 15 feet before using your remote.
no response from
your home
entertainment
component?
Cinema 6 not learn-	Make sure your remote controls are nose-to-nose
ing a command from	and are no more than 2 inches apart (see diagram
your original remote	in step 5 on page 22).
control?
Tried “Search	Try the “Search Method” again after clearing out the
Method” and still did	device key as follows: Press and hold SETUP until
not find the code?	red light blinks twice, then release. Next enter 9 - 9 -
	2. Then press and release the device key to be
	cleared twice.
Sony’s Picture In	Press TV once. Press and hold SETUP until red
Picture (PIP) won’t	light blinks twice, then release. Enter 9 - 9 - 4 and
turn off?	press SETUP once. Then enter 6 - 2 - 1 and press
	PIP On/Off. The red light should blink twice. PIP
	should operate properly now.
Sharp’s Picture In	Sharp’s PIP feature requires separate PIP functions
Picture (PIP) won’t	for “on” and “off”.
work properly?	For PIP “on”, pressTV once. Press and hold SETUP
	until red light blinks twice, then release. Enter 9 - 9 - 4
	and press SETUP once. Enter 3 - 4 - 8 and press PIP
	On/Off. The red light should blink twice. PIP “on”
	should operate properly now.
	For PIP “off”, pressTV once. Press and hold
	SETUP until red light blinks twice, then release.
	Enter 9 - 9 - 4 and press SETUP once. Enter 6 - 0 - 6
	and press SETUP PIP On/Off. The red light should
	blink twice. PIP “off” should operate by pressing
	SETUP then the PIP key.
Web Site : http://www.oneforall.com

28 29