■There’s no picture from a source connected to an HDMI IN
Reliable operation with an
■The
On your TV, make sure that the video input to which — the AV receiver is connected is selected.
When the AV receiver doesn’t connect TV with | — |
HDMI, onscreen menus are not displayed. |
|
|
|
Tuner
■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light
Relocate your antenna. | — |
Move the AV receiver away from your TV or com- | — |
puter. |
|
Listen to the station in mono. | 23 |
|
|
When listening to an AM station, operating the | — |
remote controller may cause noise. |
|
Passing cars and airplanes can cause interference. | — |
|
|
Concrete walls weaken radio signals. | — |
If nothing improves the reception, install an outdoor | — |
antenna. |
|
Remote Controller
■The remote controller doesn’t work
Before operating this unit, be sure to press | — |
RECEIVER. |
|
|
|
Make sure that the batteries are installed with the | 5 |
correct polarity. |
|
Install new batteries. Don’t mix different types of | 5 |
batteries, or old and new batteries. |
|
|
|
Make sure that the remote controller is not too far | 5 |
away from the AV receiver, and that there’s no |
|
obstruction between the remote controller and the |
|
AV receiver’s remote control sensor. |
|
Make sure that the AV receiver is not subjected to | — |
direct sunshine or |
|
Relocate if necessary. |
|
|
|
If the AV receiver is installed in a rack or cabinet | — |
with |
|
not work reliably when the doors are closed. |
|
Make sure you’ve selected the correct remote con- | 10, 43 |
troller mode. |
|
|
|
Make sure you’ve entered the correct remote control | 42 |
code. |
|
Make sure to set the same ID on both the AV receiver | 33 |
and remote controller. |
|
If you’ve connected a cassette tape deck, to the TV/ | 22 |
CD IN jacks, or an RI Dock to the TV/CD IN or |
|
GAME IN or VCR/DVR IN jacks, for the remote |
|
controller to work properly, you must set the display. |
|
|
|
If you cannot operate it, you will need to enter the | 42 |
appropriate remote control code. |
|
To control an Onkyo component that’s connected via | 42 |
u, point the remote controller at the AV receiver. |
|
Be sure to enter the appropriate remote control code |
|
first. |
|
|
|
To control an Onkyo component that’s not connected | 42 |
via u, point the remote controller at the compo- |
|
nent. Be sure to enter the appropriate remote control |
|
code first. |
|
|
|
Recording
■ Can’t record
On your recorder, make sure the correct input is | — |
selected. |
|
|
|
To prevent signal loops and damage to the AV | — |
receiver, input signals are not fed through to outputs |
|
with the same name (e.g., VCR/DVR IN to VCR/ |
|
DVR OUT). |
|
|
|
Others
■
In the following cases, the power consumption may 34, 38 reach up to a maximum of 35W:
1.You are using the Universal Port jack.
2.“HDMI Control” setting is set to “On”. (Depending on the TV status, the AV receiver will enter Standby mode as usual.)
■The sound changes when I connect my headphones
When a pair of headphones is connected, the listen- — ing mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct.
■How do I change the language of a multiplex source
Use the “Multiplex” setting on the “Audio Adjust” 32 menu to select “Main” or “Sub”.
■The ufunctions don’t work
To use u, you must make an uconnection and an 18 analog audio connection (RCA) between the compo- nent and AV receiver, even if they are connected dig- itally.
■Can’t control other components
If it’s an Onkyo component, make sure that the u cable and analog audio cable are connected properly. Connecting only an ucable won’t work.
Make sure you’ve selected the correct remote con- troller mode.
18
10, 43
En
47
