Register the Codes of Other Unit's Remote Controllers

Register the codes of other unit's (TV or VCR) remote controllers

Use this feature to register the remote codes of other remote control units. Please look up your TV/VCR from list of remote control codes starting on page 69.

1

While pressing and holding down

the desired MODE button (VCR or

 

TV) on the remote controller press

 

+10 and then release both buttons.

 

When you press and hold down the

 

desired MODE button, the SEND/LEARN

 

indicator lights up. When you press the

 

DISPLAY button, the indicator turns off.

 

When the SEND/LEARN indicator turns

 

off, release the buttons and the indicator

 

lights up again.

 

 

2

Use the number buttons on the

remote controller to input the

 

TV/VCR three digit remote control

 

code.

 

The SEND/LEARN indicator flashes twice

 

slowly to indicate that the command has

 

been successfully programmed.

 

If you perform an invalid operation, the

 

SEND/LEARN indicator flashes three

 

times quickly. Follow the same procedure

 

again.

 

 

Operate other units with the registered codes

If you are unable to operate other units with the RC-498DV remote, perform the registration procedures again.

RC-498DV button names

TV

VCR

 

 

 

 

 

 

 

(ON)

POWER

POWER

 

 

 

 

 

(STANDBY)

POWER

POWER

 

 

 

 

CH +

Program Channel +

Program Channel +

 

 

CH –

Program Channel –

Program Channel –

 

VOL%

Volume +

 

 

VOL

Volume –

 

A/AUDIO SEL/TV/VCR

TV/VCR

TV/VCR

VIDEO OFF/M/MUTING Mute

 

£

 

Play

7

 

Stop

¡

 

FF

1

 

FR

1

1

1

2

2

2

3

3

3

4

4

4

5

5

5

6

6

6

7

7

7

8

8

8

9

9

9

+10

+10, --/---

+10

0

0

0

ENTER/SEARCH

ENT, OK

ENT, OK

 

 

SEND/ LEARN

 

 

 

 

PROGRAMMED & LEARNING CAPABI

LITY

PRE

 

 

 

 

 

 

 

 

ON

S

 

 

 

 

 

 

 

TANDBY

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

V.V

 

 

 

 

 

 

 

 

CR

 

IINPUT SELECTTOORR

 

 

 

 

 

MODE

 

 

 

 

 

DV

RCVR

VCR

 

TV

 

D

 

 

 

 

 

 

 

 

 

ANGLE

SUBTTL

 

 

 

IO

 

 

 

 

 

LA

 

 

D

 

 

 

 

 

ST

M

AU

 

 

 

 

 

 

 

 

 

ENU

M

EN

 

 

 

 

 

PM

 

U

 

 

 

 

TO

 

 

 

 

 

 

CH

 

ENTER

 

 

VOL

 

R

 

 

UP

 

 

 

 

ET

URN

 

VIDEO OFF

 

 

SET

 

 

DISPLAY

 

DIMMER

MUTING

AUDIO SEL

 

 

 

 

 

TV / VCR

 

 

 

 

 

 

 

 

SEND/LEARN

VCR

TV

(PAUSE)

PAUSE

Erasing Registered codes

1

Remove the batteries from the

remote controller.

 

 

2

While pressing and holding down

the ON and STANDBY buttons,

 

reinsert the batteries.

STEP/SLOW

PAUSE

STEP/SLOW

 

 

 

 

 

SPEED

 

 

 

SURROUND

 

 

REPEAT RANDOM PROGRAM CLEAR

 

A-B

PICTURE COND M

FUNCTION M

 

1

2

3

 

4

5

6

 

7

8

9

 

-- / ---

ENTER

SEARCH

+10

0

SEARCH

REMOTE CONTROLLER

RC-498DV

3

Press the SEARCH button.

 

Note

The above procedure will completely remove all registered codes from the remote controller.

68

Page 68
Image 68
Onkyo DV-SP800 Register the Codes of Other Units Remote Controllers, Operate other units with the registered codes