Index to Parts and Controls

For operational instructions, refer to the page indicated in brackets.

■Front panel

1 2

3

 

4

 

5

 

 

6

7

 

 

 

 

 

 

 

 

VOLUME

 

STANDBY / ON

 

 

 

 

 

 

 

INPUT

 

ON

 

 

 

 

 

 

 

 

DVD / C D

VIDEO 1 VIDEO 2

H D

MD / TAPE

 

 

 

 

 

 

 

 

FM

AM

 

 

 

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

PHONES

 

 

SURROUND

STEREO SUBWOOFER MODE

MEMORY

FM MODE

TUNING/PRESET

ACOUSTIC

 

POWER

 

 

CONTROL

 

ON OFF

 

 

 

 

 

 

 

AV RECEIVER

TX-L5

 

 

 

 

 

 

 

 

8

9 0 -

= ~ !

@

1POWER switch [19]

Turns on the main power supply for the TX-L5. The

TX-L5 enters standby state and the STANDBY indicator lights up. Pressing the switch again to the off position (— OFF) shuts down the main power supply into the TX-L5.

•Before turning on the power, make sure all cables are properly connected.

•Turning on the TX-L5 may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the TX-L5 into a different electrical circuit.

2STANDBY/ON button, ON indicator, STANDBY indicator

[19]

When STANDBY/ON button is pressed to ON while the POWER switch is set to ON, the display will light to show the current volume setting for about 5 seconds then show the current sound input source and listening mode. Pressing the button again returns the TX-L5 to the standby state. This state turns off the display, disables control functions.

3Source indicators [23, 26]

One of these indicators lights to show the current source.

4Remote control sensor [7]

This sensor receives the control signals from the remote controller.

5Display [9]

6INPUT dial [23, 26, 35]

The INPUT dial is used to select the input source.

7VOLUME dial [23, 26]

The VOLUME dial is used to control the volume level. Turn the dial clockwise to increase the volume level and counterclockwise to decrease it.

8PHONES jack [29]

This is a standard stereo jack for connecting stereo headphones. The audio for the front right and left speakers are sent to the headphone speakers. When the headphones are plugged in, the listening mode automatically changes to STEREO and sounds are not output from the speakers.

9SURROUND button [32]

Press this button to select a surround mode for current input source.

0STEREO button [32]

Press this button to change the sound to stereo.

-SUBWOOFER MODE button [20]

Press to select the subwoofer mode.

=MEMORY button [24, 25]

This button is used to assign the radio station that is currently tuned in to a preset channel or delete a previously preset station.

~FM MODE button [23, 25]

Press to switch the reception mode between stereo and monaural. If audio is interrupted or noise interferes with audio during FM stereo broadcasting, press this button to switch to the monaural reception mode.

!TUNING/PRESET ™/£ button [23, 24]

Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display and it can be changed in 50 kHz increments for FM and 10 kHz (or 9 kHz) increments for AM. Also, These buttons make it possible to store desired radio stations under the desired preset numbers and recall them with an easy operation.

@ACOUSTIC CONTROL button/indicator [34]

Press to change the acoustic mode to enjoy more dynamic sounds by boosting the super bass/high frequency sounds.

8