Manuals / Brands / Home Audio / Stereo Receiver / Onkyo / Home Audio / Stereo Receiver

Onkyo TX-NR609 Error Messages, Changing the Speaker Setup Manually, Using a Powered Subwoofer

1 88

Download 88 pages, 2.32 Mb

33

En

Error Messages

While Audyssey 2EQ® Room Correction and Speaker

Setup is in progress, one of the error messages below may

appear.

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of

the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from

that of the first measurement. Check the speaker

connection.

• Writing Error!

This message appears if saving fails. Try saving again.

If this message appears after 2 or 3 attempts, contact

your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No”

means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings

(➔page 13).

Changing the Speaker Setup Manually

You can manually make changes to the settings found

during Audyssey 2EQ Room Correction and Speaker

Setup.

See also:

• “Speaker Configuration” (➔page 46)

• “Speaker Distance” (➔page 47)

• “Level Calibration” (➔page 47)

• “Equalizer Settings” (➔page 48)

Note

• Please note that THX recommends any THX main speakers be

set to “80Hz(THX)”. If you set up your speakers using

Audyssey 2EQ Room Correction and Speaker Setup, please

make sure manually that any THX speakers are set to

“80Hz(THX)” crossover (➔page 46).

• Sometimes due to the electrical complexities of subwoofers and

the interaction with the room, THX recommends setting the

level and the distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may notice

irregular results when setting the level and/or distance of the

main speakers. If this happens, THX recommends setting them

manually.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very

low-frequency sound at a low volume level, it may not be

detected by Audyssey 2EQ Room Correction and Speaker

Setup.

If the “Subwoofer” appears on the “Review Speaker

Configuration” screen as “No”, increase the subwoofer’s

volume to the half-way point, set it to its highest crossover

frequency, and then try running Audyssey 2EQ Room

Correction and Speaker Setup again. Note that if the

volume is set too high and the sound distorts, detection

issues may occur, so use an appropriate volume level. If

the subwoofer has a low-pass filter switch, set it to Off or

Direct. Refer to your subwoofer’s instruction manual for

details.

Retry

Cancel

Ambient noise is too high.

2EQ: Auto Setup

AUDYSSEY

Error message

Contents

Main AV Receiver TX-NR609 n Instruction Manual Contents E Important Safety Instructions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: WARNING Precautions For U.S. models For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS CAUTION: TO PREVENT ELECTRIC SHOCK, Supplied Accessories Declaration of Conformity Contents Introduction Turning On & Basic Operations Connections Advanced Operations Features Amplifier Processing Connections Miscellaneous Page Front & Rear Panels Front Panel Display Rear Panel Remote Controller Controlling the AV Receiver Connecting the AV Receiver Connecting the Speaker Cables Connecting Your Speakers Speaker Configuration Attaching the Speaker Cable Labels Speaker Connection Precautions Using Dipole Speakers Using a Powered Subwoofer Bi-amping the Front Speakers Connecting AV components To prevent shutter damage, hold the optical plug straight when inserting and removing. AV Cables and Jacks About AV Connections HDMI cable Other cables Y P P Connecting Components with HDMI Connecting Your Components Page Connecting Onkyo Components 1 2 3 Connecting a Recording Component Connecting the Antennas Connecting the Power Cord 1 2 Turning On/Off the AV Receiver Turning On 1 Turning Off Playback Selecting the Language for the Onscreen Setup Menus Playing the Connected Component 4 1 2 1 2 3 4 Extended Mode (Music) control Extended Mode (Video) control 1 2 3 4 Listening to Internet Radio 1 3 1 2 3 4 5 1 3 Windows Media Player 11 Setup Windows Media Player 12 Setup Playing Music Files on a Server 1 2 3 4 5 1 2 3 4 5 Remote Playback 1 2 3 4 5 Using Remote Playback Using the Tuner 1 2 3 4 5 1 2 1 2 Presetting AM/FM Stations Using RDS (excluding North American and Taiwan models) 1 2 1 2 3 4 1 2 1 2 3 4 1 2 Using Basic Functions Measurement procedure Using the Automatic Speaker Setup 1 2 3 4 5 6 7 8 Error Messages Changing the Speaker Setup Manually Using a Powered Subwoofer Selecting Listening Modes Using the Listening Modes About Listening Modes Onkyo-Original DSP Listening Modes Listening Modes Page Page Page Using the Home Menu 1 2 Using the Sleep Timer 1 Setting the Display Brightness 1 Displaying Source Information 1 Changing the Input Display 2 Using the Music Optimizer 1 Muting the AV Receiver 1 AV Recording Using Headphones 1 Recording 2 3 Advanced Setup Explanatory Notes On-screen Setup Menus Common Procedures in Setup Menu 1 Input/Output Assign Component Video Input Digital Audio Input Speaker Settings Speaker Setup Speaker Configuration Speaker Distance Level Calibration Equalizer Settings THX Audio Setup 1 2 3 Audio Adjust Multiplex/Mono Dolby DTS Audyssey DSX Source Setup Page IntelliVolume A/V Sync Name Edit 1 2 1 2 3 Picture Adjust Audio Selector Charge Mode Volume Setup Listening Mode Preset 1 Miscellaneous 2 OSD Setup Remote ID 1 2 Auto Standby Network Firmware Update Remote Mode Setup Tone Control Settings Speaker Levels 1 2 1 2 Late Night Music Optimizer Re-EQ Zone 2 Connecting Your Zone 2 Speakers Directly to the AV receiver Connecting the Zone Speakers to an Additional Amplifier Making Zone 2 Connections Adjusting the Volume for Zone 2 1 2 3 1 2 1 1 2 iPod/iPhone Playback via Onkyo Dock UP-A1 Dock Using the Onkyo Dock RI Dock Controlling Your iPod/iPhone With the RI Control Without the RI Control : Available buttons Controlling Other Components Preprogrammed Remote Control Codes Looking up for Remote Control Code 1 2 1 Controlling Other Components 2 3 Resetting REMOTE MODE Buttons 1 2 Resetting the Remote Controller 1 2 : Available buttons Troubleshooting Power Audio Only the front speakers produce sound Only the center speaker produces sound The surround speakers produce no sound The center speaker produces no sound The front high and surround back speakers produce no sound Video Tuner Remote Controller Theres no sound Theres no video UP-A1 Dock for iPod/iPhone Recording Zone 2 Music Server and Internet Radio USB Device Playback Others 1 2 Network/USB Features Network Requirements Connecting to the Network Server Requirements USB Device Requirements Supported Audio File Formats About DLNA Firmware Update Before you start Update procedure Updating the Firmware via Network 1 7 Updating the Firmware via USB 1 2 3 7 Troubleshooting 8 9 10 11 13 12 Connection Tips and Video Signal Path Video Connection Formats Audio Connection Formats * 1 * About HDMI Supported Audio Formats About Copyright Protection Using an RIHD-compatible TV, Player, or Recorder About -compatible components Operations that can be performed with connection 1 2 3 4 Specifications Amplifier Section Tuner Section Video Section General Video Resolution Chart * 2 9 4 0 0 6 3 7 *