Onkyo TX-NR708 Source Setup, Audyssey DSX, Theater-Dimensional, LFE Level, PLIIz Height Gain

■PLIIz Height Gain

The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, “Low”, “Mid” and “High”, and the front high speakers are accentuated in that order. While “Mid” is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.

`Low:

Low PLIIz Height Gain becomes active.

`Mid:

Medium PLIIz Height Gain becomes active.

`High:

High PLIIz Height Gain becomes active.

Note

•If the “Front High” settings is set to “None” (➔ 45), this setting cannot be selected.

■Dolby EX

This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.

`Auto:

If the source signal contains a Dolby EX flag, the Dolby EX or THX Surround EX listening mode is used.

`Manual:

You can select any available listening mode.

Note

•If the “Surr Back” setting is set to “None” (➔ 45), this setting cannot be selected.

•If the “Front High” or “Front Wide” setting is enabled (➔ 45), this setting is fixed at “Manual”.

DTS

■Neo:6 Music Center Image

`0 to 2 to 5

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel.

Setting a value “0” in the middle is set to hear a sound. Sound is spread in left and right (the outside) so that the set value is made big. Please adjust by liking.

Audyssey DSX™

■Soundstage

`–3dB to Reference to +3dB

With this setting, you can adjust the soundstage when using Audyssey DSX™.

Note

•If the “Center” setting is set to “None”, or both “Front High” and “Front Wide” settings are set to “None” (➔ 45), this setting cannot be selected.

Theater-Dimensional

■Listening Angle

`Wide:

Select if the listening angle is 40 degrees.

`Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen- sional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left speaker	Front right speaker
	20°/40°

LFE Level

■Dolby Digital*1, DTS*2, Multich PCM, Dolby TrueHD, DTS-HD Master Audio, DSD*3

`–QdB,–20dB,–10dB, or 0dB

With these settings, you can set the level of the LFE (Low Frequency Effects) channel individually for each input sources.

If you find that low-frequency effects are too loud when using one of these sources, change the setting to –20 dB or

–QdB.

*1 Dolby Digital and Dolby Digital Plus sources.

*2 DTS and DTS-HD High Resolution Audio sources. *3 DSD (Super Audio CD) sources.

Source Setup

Items can be set individually for each input selector.

Preparation

Press the input selector buttons to select an input source.

Main menu Source Setup

Audyssey

When Audyssey MultEQ® Room Correction and Speaker Setup is complete, the “Equalizer” (➔ 47) will be set to “Audyssey” and the “Dynamic EQ” will be set to “On”.

■Dynamic EQ

`Off:

Audyssey Dynamic EQ® off.

`On:

Audyssey Dynamic EQ on.

The Dynamic EQ indicator will light (➔ 9).

En

49