Video, Tuner, Remote Controller, There’s no picture

When playing DTS program material, using the	—
pause, fast forward, or fast reverse function on your
player may produce a short audible noise. This is not

amalfunction.

■The beginning of audio received by an HDMI IN can’t be heard

Since it takes longer to identify the format of an	—
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately.

Video

Make sure that all video connecting plugs are pushed	17
in all the way.

Make sure that each video component is properly	18, 19,
connected.	74
If your TV is connected to the HDMI OUT, select	43
“- - - - -” in the “HDMI Input” setup to watch com-
posite video, and component video sources.

If the video source is connected to a component	19, 43
video input, you must assign that input to an input
selector, and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT.
If the video source is connected to a composite video	19
input, your TV must be connected to the HDMI
OUT or the corresponding composite video output.

If the video source is connected to an HDMI input,	18, 43
you must assign that input to an input selector, and
your TV must be connected to the HDMI OUT.
While the Pure Audio listening mode is selected, the	—
video circuitry is turned off and only video signals
input through HDMI IN can be output.

On your TV, make sure that the video input to which	—
the AV receiver is connected is selected.

■There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is 91 not guaranteed. In addition, video signals from a PC are not guaranteed.

When the Resolution is set to any resolution not sup- 43 ported by the TV, no video is output by the HDMI outputs.

If the message “Resolution Error” appears on the — AV receiver’s display, this indicates that your TV

does not support the current video resolution and you need to select another resolution on your DVD player.

(European, Australian and Asian models) Specify 54 the TV system used in your area in the TV Format Setup.

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

When the AV receiver doesn’t connect TV with	—
HDMI, onscreen menus are not displayed.

(European, Australian and Asian models) Specify 54 the TV system used in your area in the TV Format.

Depending on the input signal, the on screen display 54 may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT.

■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.	—
Move the AV receiver away from your TV or com-	—
puter.
Listen to the station in mono.	32

When listening to an AM station, operating the	—
remote controller may cause noise.
Passing cars and airplanes can cause interference.	—

Concrete walls weaken radio signals.	—
If nothing improves the reception, install an outdoor	—
antenna.

Before operating this unit, be sure to press	—
RECEIVER.

Make sure that the batteries are installed with the	4
correct polarity.
Install new batteries. Don’t mix different types of	4
batteries, or old and new batteries.

Make sure that the remote controller is not too far	4
away from the AV receiver, and that there’s no
obstruction between the remote controller and the
AV receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to	—
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.

If the AV receiver is installed in a rack or cabinet	—
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you’ve selected the correct remote con-	11, 80
troller mode.

When using the remote controller to control other	—
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control	79
code.

Make sure to set the same ID on both the AV receiver	54
and remote controller.

If it’s an Onkyo component, make sure that the u	20
cable and analog audio cable are connected properly.
Connecting only an ucable won’t work.

Make sure you’ve selected the correct remote con-	11, 80
troller mode.
If you’ve connected a cassette tape deck, to the TV/	27
CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
controller to work properly, you must set the display.

If you cannot operate it, you will need to enter the	78
appropriate remote control code.