R (red)
L (white)

Connections (TX-SR700/700E)

Here is an explanation of typical ways to connect various components to the TX-SR700/700E. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features to ascertain which method of connection is best.

: Signal flow

ANTENNA

 

 

GND

 

 

 

COMPONEN

 

 

 

INPUT 2 INPUT 1

 

 

R

L

FM

AM

PHONO IN

75

 

 

 

1. CD player (CD)

DIGITAL INPUT

DIGITAL

 

VIDEO 3

VIDEO 2

VIDEO 1

DVD

 

 

OUTPUT COAXIAL

IN

OUT

IN

OUT

IN

IN

2

OPTICAL

OPTICAL

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

COAXIAL

 

 

 

 

 

 

Digital audio output (optical)

 

 

DIGITAL

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

OUT

IN

IN

OUT

IN

OUT

IN

FRONT

L (white)

L

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

SUBWOOFER

 

 

 

 

 

 

 

 

 

PRE OUT

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

R

Analog audio output

 

 

 

 

 

 

 

 

CD

TAPE

VIDEO 3

VIDEO 2

VIDEO 1

 

R (red)

Analog audio output

Ground wire (earth)

2. Turntable (PHONO)

3.Cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

L (white)

Analog audio output

R(red)

L (white)

Analog audio input

R (red)

Connecting your audio components

Below is an example of how you can connect your audio components to the TX-SR700/700E. Refer to the diagram above for the following connection examples.

AUDIO IN/OUT

These are the analog audio inputs and outputs. There are seven audio inputs and three audio outputs on the rear panel. The audio inputs and outputs require RCA-type connectors.

DIGITAL INPUT/OUTPUT

On the rear panel of the TX-SR700/700E, there are one coaxial digital input, two optical digital inputs, one coaxial digital output, and one optical digital output. To the digital inputs, connect CD players, LD players, DVD players, or other digital source component. To the digital outputs, connect MD recorders, CD recorders, DAT decks, or other similar components.

•Since an analog connection must be made when using REC OUT or ZONE 2, make sure that the connection to the input source is not digital only, but analog as well.

•When using an optical input or output jack, always use an optical fiber cable.

1.Connecting a compact disc player (CD)

Using an RCA audio cable, connect the output jacks of the compact disc player to the CD audio jacks of the TX-SR700/700E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the compact disc player has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the TX-SR700/700E depending on the type of connector on the compact disc player.

With the initial settings of the TX-SR700/700E, the CD input source is set for digital input at the OPTICAL 1 jack (OPT 1). If the digital connection is made to a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 53).

2. Connecting a turntable (PHONO)

Using an RCA audio cable, connect the output jacks of the turntable to the PHONO audio jacks of the TX-SR700/700E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

Note:

The TX-SR700/700E is designed for use with moving magnet cartridges. For proper operation, connect a ground (or earth) wire to the GND terminal. For some turntables, however, connecting the ground wire may cause increased noise, and in such a case, a ground wire is not necessary and should not be connected.

3.Connecting a cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Using RCA audio cables, connect the output jacks (PLAY) of the device to the TAPE IN audio jacks of the TX-SR700/700E and connect the input jacks (REC) of the device to the TAPE OUT audio jacks of the TX-SR700/700E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks. If the device has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the TX-SR700/700E depending on the type of connector on the device.

With the initial settings of the TX-SR700/700E, nothing is allocated as the digital input source for TAPE (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 53).

If the device has a digital input, connect it to the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack of the TX-SR700/700E for digital recording of the signal from the digital input of the TX-SR700/700E.

Note:

The output from the DIGITAL OUTPUT jack of the TX-SR700/ 700E is only the digital signal input to the DIGITAL INPUT jack.

16