Connections (TX-SR700/700E)

Connecting a DVD Player with 5.1-Channel Output

ANTENNA

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

COMPONENT VIDEO

 

 

 

 

 

 

 

 

 

 

INPUT 2

INPUT 1

OUTPUT

 

 

 

 

 

 

 

R

L

 

 

 

Y

 

Y

 

 

FM

AM

 

PHONO IN

 

 

 

 

 

 

75

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PB

 

PB

Component video output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

 

 

 

 

 

 

 

PR CONTROL

PR

 

DIGITAL INPUT

DIGITAL

VIDEO 3

VIDEO 2

VIDEO 1

DVD

MONITOR

ZONE 2

 

 

 

 

OUTPUT COAXIAL

IN

OUT

IN

OUT

IN

IN

OUT

 

 

 

OPTICAL

OPTICAL

 

 

 

 

 

 

 

12V

 

 

2

 

 

 

 

 

 

V

TRIGGE

 

Video ouput

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

 

S

IR

 

S video output

 

 

 

 

 

 

 

 

 

IN

 

 

 

COAXIAL

 

 

 

 

 

 

 

 

 

 

 

 

DIGITAL

 

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

IN

OUT IN

IN

OUT

IN

OUT

IN

FRONT

SURR CENTER

 

 

 

L

 

 

 

 

 

 

 

L

 

 

 

SUBWOOFER

 

 

 

 

 

 

 

 

 

 

4. DVD player (DVD)

 

 

 

 

 

 

 

 

 

 

 

PRE OUT

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD

TAPE

VIDEO 3

VIDEO 2

VIDEO 1

 

SUB

 

 

 

 

WOOFER

 

 

 

 

 

 

 

 

 

 

 

DVD

 

Analog audio output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(center)

 

 

 

 

 

 

 

 

 

 

 

Analog audio output

 

 

 

 

 

 

 

 

 

 

 

(subwoofer)

 

 

 

 

 

 

 

 

 

 

 

L (white)

Analog audio output

 

 

 

 

 

 

 

 

 

 

 

R (red)

(surround L/R)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L (white)

Analog audio output

 

 

 

 

 

 

 

 

 

 

 

R (red)

(front L/R)

 

 

 

 

 

 

 

 

 

 

 

 

: Signal flow

 

 

 

 

 

 

 

 

 

 

 

Digital audio output

 

 

 

 

 

 

 

 

 

 

 

 

(coaxial)

Connecting your video components

Below is an example of how you can connect your video components to the TX-SR700/700E. Refer to the diagram above for the following connection examples.

COMPONENT VIDEO INPUT/OUTPUT

For DVD players or other devices that have component video connectors, the TX-SR700/700E has two banks of component video input connectors (Y, PB, PR) for direct component video input. The TX-SR700/700E also has one bank of component video output connectors for direct component video output to the matrix decoder of a television, projector, or other display device. By sending the pure component video signal directly, the signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly lifelike colors and crisp detail.

•The signal that comes in from COMPONENT VIDEO INPUT is only sent to COMPONENT VIDEO OUTPUT. When connecting a video player to the COMPONENT VIDEO INPUT jacks, be sure to connect your television to the COMPONENT VIDEO OUTPUT jacks.

VIDEO IN/OUT

These are the video inputs and outputs. On the rear panel, there are four video inputs and two video outputs and each one includes both composite video and S video configurations.

Connect VCRs, VTRs, LD players, DVD players, and other video components to the video inputs. Connect VCRs, VTRs, and other recording components to the video outputs to make video recordings.

•When connecting a VCR or other video component, make sure you connect its audio and video leads to the same bank (e.g., both to VIDEO 3).

•The VIDEO 4 inputs are located on the front panel.

The flow of the video signals is as follows:

The signal that comes in from a VIDEO IN jack is sent to both the VIDEO OUT and S VIDEO OUT jacks. The signal that comes in from a S VIDEO IN jack is sent to both the S VIDEO OUT and VIDEO OUT jacks. It is not necessary to make both video and S video connections.

Notes:

•If your video output device (e.g., television or projector) is connected only to the MONITOR OUT VIDEO jack, MONITOR OUT S VIDEO jack, or both, and the video signal from the source component is input through the component video connectors, no picture will appear. Video sources input from the component video connectors can only be output from the component video connectors.

•For more information about the DIGITAL INPUT/OUTPUT jacks, see page 16.

17