Oreck ORB480 warranty Hard Floor Cleaning Accessories, Except wood and marble

Hard Floor Cleaning Accessories

HEAVY-DUTY CLEANING FOR HARD SURFACE FLOORS

(except wood and marble)

EQUIPMENT AND MATERIALS REQUIRED:

1.	Orbiter floor machine	5. Oreck O Monster® All Purpose Cleaner
2.	Black Drive Pad Holder	6. Broom or Dust Mop
3.	Brown Pad	7. Cleaning Solution
4.	Brush	8. Mop & Bucket

PROCEDURE:

This method uses Oreck O Monster® All-Purpose Concentrated Cleaner to remove dirt, grease, oil, food, shoe scuff marks, and general grime from hard flooring. The effectiveness of the cleaning is a direct function of the concentration of the cleaning agent and the aggressiveness of the pad or brush being used.

1.VACUUM OR SWEEP FLOOR

Clean the floor with a broom or dust mop or Oreck vacuum cleaner.

2.MIX CLEANING SOLUTION

Mix the Oreck All-Purpose Concentrated Cleaner with warm water according to the directions on the bottle.

3.APPLY SOLUTION

Apply solution to floor in a 6’x6’ area. Do not flood the floor!

4.SCRUB WITH BROWN PAD OR BRUSH

Scrub floor with Orbiter using the Drive Pad Holder with the Brown Pad or the Brush for grouted floors.

5.REMOVE SOLUTION FROM FLOOR

Pick up dirty solution with a mop or wet-dry vacuum or use the Orbiter with a carpet bonnet to mop. Do not allow cleaning solution to dry on floor.

6.FINISH

Rinse floor area with clean water and a clean mop. Change water frequently.

Helpful Hints:

Clean Hard to Reach Places: Remove the center part of the pad. Use this to scrub hard to reach areas such as corners and around door jambs.

Do not flood the floor areas with cleaning solution.

Do not allow the cleaning solution ot dry on the floor before pickup.

Use a clean mop for final rinse. Change rinse water frequently.

Please check with your floor manufacturer’s remommendations on how to clean your particular floor. Some floors require certain procedures.

All word marks, logos, product configurations, and registered trademarks are owned and used under the authorization of Oreck Holdings, LLC. © 2001 Oreck Holdings, LLC. All Rights Reserved. Printed in America

53303-01 REV B	8
09/02 ECN# R-6644

DRIVE PADS
DRIVE PAD HOLDER (Black plastic with teeth)	53178-51-0327
FLOOR PADS
POLISHING PAD (White fiber)	437051

For a higher polishing gloss use the LAMBS WOOL BONNET.

SCRUB PAD (Brown fiber)	437049
STRIP PAD (Black fiber)	437071

For all floor pads, place either DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place the pad on the floor and center Orbiter onto the pad.

FLOOR BRUSHES
SHAMPOO BRUSH (Black bristle)	237049

Use with ORECK DRY SHAMPOO (OC8). This brush has specially cut bristles to provide safe, soft action needed for carpet cleaning.

POLISHING BRUSH - UNION MIX (Tan bristles) 237048

This polishing brush can be used to polish wood floors. This brush will “blend” in excess floor wax, maintain an even coat of wax and eliminate wax buildup.

SCRUB BRUSH (Orange bristles) 237047

This brush is used to clean ceramic and concrete and many tough stains.

GRIT BRUSH (Hard green/gray bristles) 237056

This is an extremely aggressive brush used to scour tough stains on concrete and asphalt.

All the floor brushes snap directly onto the Orbiter with no drive pad. Remove the brushes from the machine after use so as not to damage them.

OTHER ACCESSORIES
LAMBS WOOL BONNET	437054

This bonnet is designed to provide the best possible shine on wood, tile and vinyl floors. To install bonnet, place over the DRIVE PAD HOLDER. Pull the drawstrings tight to prevent slipping. Tie a bow and tuck the excess string inside the bonnet. After the floor has been waxed, use the bonnet for everyday buffing to remove scuff marks. When the bonnet becomes dirty, wash with soap and water, wring it out and place it back on the DRIVE PAD HOLDER to dry to its original shape.

CARPET SHAMPOO BONNET 437053

This bonnet cleans the traffic lane and spots in the carpet without wetting the entire carpet. Use with ORECK PREMIST (Part No. 24CPTSPR) or carpet shampoo. When one side of bonnet is dirty, flip it over and use the other side. When bonnet is completely soiled, hose off and air dry.

SAND SCREENS

The very best in floor sanding. For all sand screens, place either DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place the sand screen under any floor pad on floor and center Orbiter onto the pad. The SAND SCREEN comes in 60 grit (SS12060), 80 grit (SS12080), 100 grit (SS12100) and 120 grit (SS12120).