Redial
1.Lift the handset.
2.Press Redial to redial the last number dialled.
Volume control
The handset earpiece volume may be increased or decreased during a call. Press the Volume button to increase or decrease the volume.
Recall (Australia ONLY)
You can use the Recall button on your telephone when using your network operator’s services such as call waiting etc. A subscription may apply for these services, contact your network operator for more information. If this is not working correctly check the country option in the phone menu and select Australia or New Zealand options. For Australia it should be set to 100ms and for New Zealand 600ms.
Mute button
The handset volume can be muted during a call by pressing MUTE button. Release the MUTE button to reactivate the microphone.
Ringer volume control
The ringer volume can be adjusted using the Ring Volume switch located on the
Memory
This telephone has 10
Storing One-Touch Memories
1.Ensure the Program/Store switch is set to Store.
2.Lift the handset, the dial tone will be heard (ignore any tone). Press Store button.
3.Enter the telephone number to be stored (up to 32 digits). Press Store.
4.Select a memory position by pressing the corresponding memory button.
5.Replace the handset.
If you need to insert a pause in the telephone number press
Redial
If you need to change a number, store the new number in the same location as the old one.
Dialling using
1.Lift the handset, the dial tone will be heard.
2.Press the required
Messages button
You can also store a telephone number into this button like the one touch memory buttons:
1.Ensure the Program/Store switch is set to Store.
2.Pick up the handset, the dial tone will be heard. (ignore the dial tone) press Store button.
3.Enter the telephone number to be stored (up to 32 digits). Press Store.
4.Press the Messages button, now number have been stored.
5.Replace the handset.
Dial the pre-programmed number
1.Lift the handset. You will hear the dial tone.
2.Press the MESSAGES button. A pre programmed number will be dialed automatically.
Line Switch
There is a line switch on the top of the unit which allows you to select the desired telephone line 1 or line 2 depends on your selection.
You may configure the phone using the switch located under the inlay on the base of the phone marked 1 and 2 so that the telephone (1) and the outer port (2) are connected in parallel.
Connection of additional equipment
Additional equipment such as modems can be connected to this telephone via the DATA PORT socket on the right side of the base. Two methods of operation can be selected by using the switch located
on the top of the base (Please refer to "Location of controls" point 12):
1.Allows for single line parallel operation. For example, a computer modem can be operated through the telephone but only one device can be operated at a time, either the modem or the telephone.
2.Allows for two line operation where a computer modem can be connected via the telephone and both devices can be used at the same time. The network wall socket must have two lines connected.
Hearing aid compatible
This telephone is hearing aid compatible. Select the T mode on your hearing aid to enable this feature.
Programmer lock
The Program/Store switch (located under the underlay) allows access to the
Store Manual programming allowed. Program Programmer downloads allowed.
PBX Message Waiting
Most PBX systems use a function called Message Waiting. The telephone will indicate when a call was received by flashing the Massage Waiting lights next to the Messages button.
The MW switch is located on the top side of the telephone. The MW function operates differently depending on the PBX in question.
Please contact the PBX administrator for more information. The following four alternatives are available: LED+, 
) and high DC voltage (HV).
When the telephone is used in systems without a telephone exchange ( 
) should be selected.
Programmer
A dedicated programmer (optional) can be connected to the Programmer socket located on the top side of the telephone, this allows easy programming of the 10 One- Touch memories and the number in Messages key.
The Program/Store switch (located on the top side of the telephone) must be set to Program.
