Installation Guide
Ceiling Flush Mount Bracket
Indoor Use Only
Please read this document before using the product, and save this document for future reference.
Panasonic Network Camera Website:
http://www.panasonic.com/netcam
for customers in the USA and Puerto Rico
Model No.
Please read the Operating Instructions included with the camera before proceeding.
•This document (Installation Guide) explains how to install the
Abbreviations
•The Ceiling Flush Mount Bracket is referred to as “the bracket” in this document.
•The Network Camera is referred to as “the camera” in this document.
Preparation
1.Confirm the following items are included in the bracket’s packaging.
• Additional pieces can be ordered by calling
Ceiling Flush Mount Bracket | Washer (1 pc.) | Template (1 pc.) |
(1 pc.) | Order No. XWG4F16VW | Order No. PNPD1087Z |
| Used when securing the safety | Used as a references when |
| wire to the ceiling. | making a hole in the ceiling. |
Ceiling Mounting Cover (1 pc.) | Screw A (1 pc.) | Screw B (4 pcs.) |
Order No. PQKL10092Z1 | Order No. XTB4+20AFJ | Order No. XYN4+F6FJ |
Used when mounting the camera | Used to secure the safety wire to | Used to secure the camera |
on a ceiling. | the ceiling. | (3 pcs.) and the safety wire (1 pc.) |
|
| to the bracket. |
Safety Wire (1 pc.) | Connector Cover (1 pc.) | Installation Guide |
Order No. PQME10080Z | Order No. PNHX1058Z | (this document) (1 pc.) |
Used to secure the bracket when | Used to protect the cables when |
|
mounting it. | mounting the camera. |
|
2.You will need the following additional items to install the bracket.
– 1 anchor bolt and 2 nuts (see step 2 and 6 on page 2)
Important Information Regarding Camera Mounting
Please read the following information before mounting the camera. Consult an authorized dealer for mounting.
Caution
• Make sure you attach the safety wire when mounting the bracket and the
camera on a ceiling to prevent them from falling. |
|
Note | At least 80 mm (3 1/8 inches) |
| |
• This product should only be used with the |
|
• If using an SD memory card, insert the card before installing the camera in |
|
the bracket. |
|
• Use screws that are appropriate for the material of ceiling. | Ceiling board: Max. 40 mm (1 9/16 inches) |
•The included screws are for use with wooden ceilings only.
•To ensure that camera images are displayed properly, do not mount the
bracket on an incline. | • The illustration below is an example of a completed installation, when looking |
• The camera’s MAC address and serial number are printed on the bottom of | at the rear of the camera. |
the camera and are needed in order for camera configuration and |
|
maintenance. Make a note of both of them for before mounting the camera. |
|
• Mounting and cabling instructions described in this document follow |
|
generally accepted guidelines suitable for residential installations. In some |
|
areas, commercial and industrial installations are regulated by local or state |
|
ordinances. For such installations, contact your local building department or |
|
building inspector for more details. |
|
• Camera images can be viewed in relatively dark areas, however, image |
|
quality decreases when viewing dark images. We recommend using |
|
supplemental lighting for best results. |
|
•Prolonged exposure to direct sunlight or halogen light may damage the camera’s image sensor. Mount the camera appropriately.
•When mounting the camera, make sure to wrap the AC adaptor cord (if used) and other cables (external microphone or speaker cable, video cable, etc.) around the hooks as shown to ensure secure connections.
•Do not directly touch the lens cover. Clean the lens cover with a dry and soft cloth if necessary.
•There must be at least 80 mm (3 1/8 inches) of space above the ceiling board where this product will be installed.
•The ceiling board must be no more than 40 mm (1 9/16 inches) thick.
© 2008 Panasonic Communications Co., Ltd. All Rights Reserved. PQQX16477ZA KK0108CM0