raise the moving blade, and brush the cut hairs out from between the blades. (see fig. 18)

4.Apply a few drops of the oil to the points indicated by the arrows. (see fig. 16)

5.Remount the blade on the trim- mer body.

ATTENTION:

(A nickel cadmium battery that ) is recyclable powers the product you have purchased. Please call

1-800-8-BATTERY for information on how to recycle this battery.

7.Remove the two screws (l) and disconnect the rubber push plate

(m).(see fig. 21)

8.Remove the screws (n) and dis- connect housing (o).

9.Disconnect the battery chamber

(p)and remove the battery (q). (see fig. 22)

specifically designed for this model. Use only the included AC adaptor.

7.

Do not pull, twist or severely bend

 

the power cord.

8.

Do not wrap the power cord tightly

 

around the appliance.

9.

Dry the trimmer completely be-

 

fore charging it.

10. Keep the adaptor away from wa-

Blade life

Blade life will vary according to the frequency and length of use. For ex- ample, using the unit for 10 minutes every 3 days, the life expectancy is approximately 3 years. If cutting effi- ciency is reduced substantially de- spite proper maintenance, the blades have exceeded their service life and should be changed.

The replacement par t no. is WER9602.

Battery life

Battery life will vary according to the frequency and length of use. If the battery is charged 3 times a month, the service life will be approximately 6 years. If the unit is left without be- ing charged for more than 6 months, the charge will drain from the battery and their service life may be short- ened. Therefore, even when not us- ing regularly, it is recommended that the unit be recharged at least once every 6 months.

How to remove the built-in re- chargeable battery before dis- posal of the trimmer

The battery in this trimmer is not in- tended to be replaced by consu- mers. However, the battery may be replaced at an authorized service center. The procedure described be- low is intended only for removal of the rechargeable battery for the pur- pose of proper disposal.

Always make sure that the battery have been removed from the trimmer before disposing of it.

1.Disconnect the adaptor from the AC outlet, and remove the power cord from the trimmer.

2.Remove the blade from the trim- mer.

Remove the screw (a) and detach the bottom cover (b). (see fig. 19)

3.Detach the dial cover (c), remove the screw (d) and disconnect the dial (e).

4.Remove the two screws (f).

5.Detach the housing (g), front panel (h) and side panel (i), then remove the trimmer drive rod (j) (see fig. 20).

6.Remove the two screws (k).

Attention

Do not charge the trimmer at tem- peratures below 0°C (32°F) or above 40°C (104°F), or where it will be exposed to direct sunlight, or other heat sources.

Do not continue charging for more than 48 hours. Doing so may dam- age the battery.

Clean the housing only with a soft cloth slightly dampened with water or soapy water. Never use a caus- tic cleaner such as benzene or bleach.

The trimmer may become warm during operation and normal re- charging. This is normal.

Caution

1.Keep out of reach of children.

2.Never tamper with the moving parts.

3.Do not pick up the trimmer by the cord. It may become detached, causing damage or injury.

4.Do not use on animals.

5.Never disassemble the trimmer. Take it to a qualified serviceperson when service or repair is required.

6.Do not attempt to use any power cord or adaptor other than one

ter and handle it only with dry

hands.

11. Store the adaptor in a dry area

where it will be protected from

damage.

12. Wash the trimmer in tap water. Do

not use salt water or boiling wa-

ter. Also, do not use cleaning

products that are designed for

toilets, bathrooms or kitchen ap-

pliances. Do not submerge the

trimmer for a long time.

13. Do not take the housing apart as

this can affect the watertight con-

struction.

14. Do not clean with water when the

trimmer is connected to the power

cord.

15. This power unit is intended to be

correctly oriented in a vertical

position or floor mount position.

This product is intended for house- hold use only.

Specifications

Power source: 120 V AC, 60 Hz

Motor voltage: 1.2 V DC

Charging time: 8 hours

10

11

Page 6
Image 6
Panasonic ER224 operating instructions Blade life, Battery life, Specifications