Forward / Reverse lever Operation
(Forward ( 
), Neutral, Reverse ( 
))
CAUTION:
•Do not operate Forward/ Reverse lever until the chuck comes to a complete stop. Shifting during rotation of the chuck may damage the tool.
•The trigger switch may not be locked, when the lever is set to its center position (Neutral).
•Check the direction of rotation before use.
Forward Rotation Switch Operation
1.Push the lever for forward rotation.
2.Depress the trigger switch slightly to start the tool slowly.
3.The speed increases with the amount of depression of the trigger for efficient tightening of screws and drilling. The brake operates and the chuck stops immediately when the trigger is released.
4.After use, set the lever to its center position (Neutral).
Reverse Rotation Switch Operation
1.Push the lever for reverse rotation.
2.Depress the trigger switch slightly to start the tool slowly.
3.After use, set the lever to its center position (Neutral).
Clutch Torque Setting
Adjust the Motor shut off torque by selecting one of the 18 clutch settings or
“
“ position to the application.
CAUTION:
•Test the setting before actual operation. Set the scale at this mark (
).
Vent hole
Speed Selection
Choose a low or high speed to suit the use.
The more the speed control trigger is pulled, the higher the speed becomes.
CAUTION:
•Check the speed selector switch before use.
•Use at low speed when strong force is needed during operation. (Using at high speed while a strong force is applied may cause a motor breakdown.)
*See in SPECIFICATIONS "RECOMMENDED SPEED SELECTION".
•Do not operate the speed selector switch
This can cause the rechargeable battery to wear quickly or damage the internal mechanism of the motor and gears.
•To eliminate excessive temperature increase of the tool surface, do not operate the tool continuously using two or more battery packs. Tool needs cool off time before switching to another pack.
•Do not cover vent holes on body sides of the body during operation. Otherwise, the machine function is adversely affected to cause a failure.
•Do not strain the tool (motor). This may cause damage to the unit.
•Use the machine in such a way as to prevent the air flow out of the vent holes from blowing directly onto your skin. Otherwise, you may get burnt.
For Appropriate use of Battery pack
Ni-Cd Battery pack (EY9005)
NOTE:
•Use only battery charger EY0005 for
•The ambient temperature range is between 0°C (32°F) and 40°C (104°F).
If the battery pack is used when the battery temperature is below 0°C (32°F), the tool may fail to function properly. In that case, charge the battery until charging is completed for appropriate functioning of the battery.
Battery Pack Life
The rechargeable batteries have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one.
Charging: Battery charger (EY0005)
NOTE:
•When you charge the battery pack for the first time, or after prolonged storage, charge it for about 24 hours to bring the battery up to full capacity.
1.Plug the charger into the AC outlet.
NOTE:
•Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.
2.Insert the battery pack firmly into the charger.
Battery pack
To AC outlet
Battery charger
3.During charging, the charging lamp will be lit.
When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharging.
•Charging will not start if the battery pack is too warm (for example, immediately after
The charging lamp will be red flashing until the battery cools down. Charging will then begin automatically.
4.When charging is completed, the charging lamp will start flashing quickly.
5.If the charging lamp does not light immediately after the charger is plugged in, or if after the standard charging time the lamp does not go off, consult an authorized dealer.
NOTE:
•When charging a cool battery pack (below 5°C (41°F)) in a warm place, Ieave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature.
Otherwise battery pack may not be fully charged.
•Cool down the charger when charging more than two battery packs consecutively.
•Do not insert your fingers into contact hole, when holding charger or any other occasions.
— 8 — | — 9 — |
