Panasonic GP-MF852PT Preparations, System Connections, Optional Accessories, Specifications

PREPARATIONS

SPECIFICATIONS

1.Power Supply for Camera

Prepare a regulated DC power supply which can supply DC 12 V ±10 % DC 465 mA or more current and rated CLASS 2.

2.Lenses

Be sure to use the optional manual iris lens having the following items.

Focus : Adjustable

Lens Weight : Less than 300 g (0.66 lbs.)

Note: If the lens is heavier than 300 g (0.66 lbs.), both the lens and the camera should be secured by using the support- er.

Mount : C-mount

The protrusion at the rear of the lens should be as shown in the illustration.

3.Switch Covers Removal

Caution: The following preparation should be made by qualified service personnel or system installers.

For setting the Rear Panel Switch No.1 to 8, remove the switch cover fixing screw on the rear panel as shown below.

Remove this screw

VIDEO

Pick-up Device :	Inter Line Transfer type CCD with 768 (H) x 494 (V) pixels.
Image Size :	2/3” (7.95 (H) x 6.45 (V) mm)
	Full non interlace (1/60 s)
Synchronization :	Internal or External (Selectable Automatically)
	Internal : Built-in sync generator
	External : 4.0 V[p-p]/75 Ω Horizontal drive and Vertical drive pulses
External Reset :	External signal (4.0 V[p-p]/75 Ω, negative) supplied to EXT VD IN
	connector can be used as reset signal
Horizontal Resolution :	500 lines at center
Minimum Illumination :	5 lx (0.5 foot-candles), (F1.4, Gain (+6 dB) , γ OFF)
Gamma :	1.0
Gain Selection :	0/+6 dB
Electronic Shutter :	9-step (1/100 s to 1/30 000 s) at normal
	5-step (1/2 000 s to 1/30 000 s) at Shutter Trigger
Lens Mount :	C-Mount
Vibration Resistance :	7 G (10 Hz - 150 Hz) (2 hours each for three axes)
Shock Resistance :	80 G (IEC 68) *IEC=International Electronical Technical Commission
Power Source :	DC + 12 V, 465 mA
Ambient Temperature :	−10˚C - +50˚C (14˚F - 122˚F)
Dimensions :	45(W) x 45(H) x 120(D) mm [1-25/32”(W) x 1-25/32”(H) x 4-23/32”(D)]
Weight :	270 g (0.6 lbs.) (Camera Only)

Dimensions and weight indicated are approximate values.

Specifications are subject to change without notice.

Less than 7.5 mm (1/2”)

SYSTEM CONNECTIONS

Caution: Keep the power switches of all units to OFF before connections.

1.Connect the optional camera cable GP-CA34 between the connector of this camera and the 12 V DC Class 2 power supply(not provided as an accessory).

2.Connect the video connector of the GP-CA34 to the Frame Grabber.

OPTIONAL ACCESSORIES

Camera Cable GP-CA34

GP-CA33

GP-CA59

GP-CA60

Camera

GP-CA34

12V DC

Power Supply

HD IN

VD/V reset

Video input of Frame Grabber

Caution: Use a 12 V DC Class 2

Power Supply only

EXTERNAL SYNCHRONIZATION

Full non interlace	Notes:
The GP-MF852PT works in full non interlace mode	• If the picture appears disturbed, be sure to
when external HD/VD signal is supplied to pin-6	match the phases of falling edges of the
and pin-7 of the camera connector (12-pin).	external HD/VD.
	• Normal monitor cannot display the picture
	from this camera. To display the picture, syn-
	chronize the camera and multiscan monitor
	from external HD/VD.