Panasonic SA-HE70 Presetting, Other settings, Automatic presetting, Manual presetting, Dr Comp

Presetting Other settings

TUNING		- BAND	MEMORY
2	1	– FM MODE
			VOLUME
	POWER
	w	q SFC MODE

8
SPEAKERS	- HELP	- BAND		DOWN	UP
	– RESET	– FM MODE	MEMORY
			DSP	DOLBY
	TUNING		SOUND MODE	PRO LOGIC 2
	2	1	PRESET
PHONES

DSP

SOUND MODE

PRESET

INPUT SELECTOR

		DIGITAL INPUT
TAPE MONITOR	SUBWOOFER	DVD 6CH INPUT
BASS/TREBLE	3	4
BALANCE	L	R

		SFC MODE
w	q

VOLUME

POWER
w	q	SFC MODE

8

SPEAKERS	- HELP	- BAND					DOWN	UP
	– RESET	– FM MODE	MEMORY
					DSP	DOLBY
	TUNING			SOUND MODE		PRO LOGIC 2
	2	1	PRESET

PHONES

INPUT SELECTOR

INPUT SELECTOR

		DIGITAL INPUT
TAPE MONITOR	SUBWOOFER	DVD 6CH INPUT
BASS/TREBLE	3	4
BALANCE	L	R

Automatic presetting

- BAND

1 Press [ – FM MODE ] to select “FM”.

TUNING

2Press [ 2 1 ] to tune to “FM 87.9 MHz”.

3 Press and hold [ MEMORY ].

The FM stations the unit can receive are preset in channels 1 to 30.

- BAND

4Press [ – FM MODE ] to select “AM”.

TUNING

5Press [ 2 1 ] to tune to “AM 530 kHz”.

6 Press and hold [ MEMORY ].

The AM stations the unit can receive are preset in channels 21 to 30.

(FM stations are replaced if any were preset in these channels.)

During automatic presetting, the memory indicator (˜) flashes and the frequency scrolls. The memory indicator and channel numbers are displayed for a second when a station is preset.

The last station to be preset is displayed when presetting finishes.

Manual presetting

Preset the stations one at a time.

1Tune to the station.

2 Press [ MEMORY ].

TUNING

3Press [ 2 1 ] to select a channel.

4 Press [ MEMORY ].

Selecting channels

1Press [ PRESET ].

The channel number flashes for about 5 seconds.

2 Press [	TUNING		].
	2	1

Hold down the buttons to change channels faster.

For your reference

Even if the power supply cord is disconnected from the household AC outlet, the stations remain in memory for approximately one month.

Improving reception

¡ DSP DEFEAT	DSP
Press and hold [	SOUND MODE
	] until “DEFEAT” appears.
	DSP
Press and hold [	SOUND MODE
	] again to turn the DSP on.

Note

While the DSP is defeated, you cannot:

– Select DSP sound modes,

– Adjust the tone,

– Output a test signal,

– Adjust individual speaker output, or

– Use digital input.

¡For your reference

14	DVD players can interfere with radio reception. Turn the DVD
	player off or move it further away from the antennas if this occurs.

DR COMP –

Dynamic range compression

Change this setting to listen to software recorded with Dolby Digital at low volume (such as late at night) and maintain audio clarity. It reduces the peak level in loud scenes without affecting the sound field.

OFF: The software is played with the original dynamic range (factory setting).

STANDARD: The level recommended by the producer of the software for household viewing.

MAX: The maximum allowable compression (recommended for night viewing).

1 Press [			SFC MODE ] at the same time to enter
	w	q
the setting mode.
2 Press [			SFC MODE ] to select “DR-COMP”.
	w	q

INPUT SELECTOR

3Turn [ ] to select “OFF”, “STANDARD” or

“MAX”.
4 Press [			SFC MODE ] at the same time to exit
	w	q

the setting mode.

DIMMER –

Dim the unit’s display for better viewing in a darkened room

The factory setting is OFF (normal brightness).

1 Press [			SFC MODE ] at the same time to enter
	w	q
the setting mode.
2 Press [			SFC MODE ] to select “DIMMER”.
	w	q

INPUT SELECTOR

3Turn [ ] to select “OFF” or “ON”.

4 Press [			SFC MODE ] at the same time to exit
	w	q

the setting mode.

RQT6193