How discs with MP3 differ from CDs
Marking a track
You can mark one track each on the discs loaded so that you can start play from them later.
To mark a track number
1During play or stop
Select your desired track.
(For MP3, refer to “Track skip play” on page 10.
For
2On the remote control
Hold down [MARKER] until “STORING” blinks on the display.
On the main unit AK520 AK523
Hold down [MARKER,
The selected track is stored in the marker of the current disc.
Note
If a track is already stored in the marker, it will be replaced next time you store a new track in the same marker.
To recall a marked track number in the current disc
During play or stop
On the remote control
Press [MARKER] to recall a marker.
On the main unit AK520 AK523
Press [MARKER,
Play starts from the track recalled.
Note
•“NO MARKER” indicates that the marker in the current disc is empty.
•The marker memory is cleared when you open the CD tray.
•For
•You cannot use this function during program mode.
Radio
Manual tuning
1Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button: FM ↔ AM
2Press [PLAY MODE] on the remote control to select “MANUAL”.
Every time you press the button:
MANUAL ↔ PRESET
3Hold down [g/REW/3] or [f/FF/4] for a moment to search for a station.
The frequency stops when it finds a clear station.
To stop during the process, press [g/REW/3] or [f/FF/4].
Under excessive interference, a station may not be found.
Press [g/REW/3] or [f/FF/4] repeatedly to tune
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display “MONO”.
Monaural sound is selected and noise reduces when reception is weak.
Hold down [PLAY MODE] again to cancel the mode. “MONO” is also cancelled if the frequency is changed.
Radio
To receive FM broadcasts allocated in 0.1 MHz steps
Main unit only
Hold down [TUNER, BAND]. The display changes in a few seconds to show the current minimum FM frequency. Continue to hold down the button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
Note
•After changing the “allocation” setting, the frequencies you previously preset in the memory will be cleared.
•Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast.
Preset tuning
Remote control only
There are two methods of
Automatic presetting : All the stations the tuner can receive are preset.
Manual presetting : You can select the stations to preset and the order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select “FM” or “AM”.
Automatic presetting
Do the following once each for FM and AM.
Preparation: Tune to the frequency where
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in ascending order. When finished, the last station memorized is tuned in.
AK520 |
| AK523 |
| AK320 |
| AK323 |
Manual presetting
1Press [PROGRAM] then press [g, REW/3 ] or [f, 4/FF] to tune to the desired station.
2Press [PROGRAM] then press [g, REW/3 ] or [f, 4/FF] to select a channel.
3Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
Selecting channels
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [>10], then the two digits.
OR
1Press [PLAY MODE] to select “PRESET”.
2Press [g, REW/3] or [f, 4/FF] to select the channel.
13
RQT7330
