
■ iPod or iPhone
ENGLISH | You cannot switch on the iPod or iPhone. |
• Examine that the battery of the iPod or iPhone is not depleted. | |
| • Switch off the iPod or iPhone and the system before you connect the |
| iPod or iPhone. Connect the iPod or iPhone and try again. |
| No sound |
| • Switch off the iPod or iPhone and remove from the system. Connect |
| the iPod or iPhone to the system and switch it on and play it again. |
| ■ Main unit displays |
| “NO PLAY” |
| • Examine the content. You can only play supported format. |
| “F76” or “F61” |
| • There is a power supply problem. |
| “ERROR” |
| • An incorrect operation was done. Read the instructions and try again. |
“NOT MP3/ERROR”
•An unsupported MP3 format. The system will skip that track and play the next one.
•The system cannot show the remaining play time for variable bit rate (VBR) tracks.
“NODEVICE”
• The iPod or iPhone is not connected. Examine the connection.
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
•There is no response when buttons are pressed.
•You want to clear and reset the memory contents.
To reset the memory
1Disconnect the AC power supply cord.
(Wait 3 minutes before you continue with step 2.)
2While you press and hold [1, POWER] on the main unit, connect the AC power supply cord again.
“– – – – – – –
3Release [1, POWER].
All the settings are set back to the factory preset. It is necessary to set the memory items again.
Maintenance
To clean this system, wipe with a soft, dry cloth.
•Never use alcohol, paint thinner or benzine to clean this system.
•Before using chemically treated cloth, read the instructions that came with the cloth carefully.
RQTX1249
Specifications
■Amplifier section
RMS output power stereo mode
Front Ch (both ch driven)
5 W per channel (6 | ), 1 kHz, 10% THD |
Total RMS stereo mode power | 10 W |
FTC output power stereo mode |
|
Front Ch (both ch driven) |
|
4.5 W per channel (6 ), 60 Hz to 20 kHz, 10% THD | |
Total FTC stereo mode power | 9 W |
■FM/AM tuner, terminals section
Preset station | FM 30 stations |
| AM 15 stations |
Frequency modulation (FM) |
|
Frequency range | 87.9 MHz to 107.9 MHz (200 kHz step) |
| 87.5 MHz to 108.0 MHz (100 kHz step) |
Antenna terminals | 75 (unbalanced) |
Amplitude modulation (AM) |
|
Frequency range | 520 kHz to 1710 kHz (10 kHz step) |
| 522 kHz to 1629 kHz (9 kHz step) |
Headphone jack |
|
Terminal | Stereo, 3.5 mm (1/8″) jack |
AUX (rear) |
|
Terminal | Stereo, 3.5 mm (1/8″) jack |
■ Disc section
Disc played [8 cm (3″) or 12 cm (5″)]
CD, | formatted disc) |
Pick up |
|
Wavelength | 790 nm (CD) |
Laser power | CLASS I (CD) |
Audio output (Disc) |
|
Number of channels | 2 ch (FL, FR) |
FL = Front left channel |
|
FR = Front right channel |
|
■ Speaker section
Type | 1 way, 1 speaker system (bass reflex) |
Speaker unit(s) |
|
Full range | 8 cm (3 1/8″) cone type |
Impedance | 6 |
Frequency range | 60 Hz to 25 kHz |
| 90 Hz to 22 kHz |
■ General
Power supply |
| AC 120, 60 Hz |
Power consumption |
| 14 W |
Dimensions (W x H x D) |
| 400 mm x 221 mm x 110 mm |
|
| (15 3/4″ x 8 3/4″ x 4 1/2″) |
|
| [D = 69 mm (2 3/4″) minimum] |
| [D = 149 mm (5 3/4″) tray open] | |
Mass (weight) |
| 2.1 kg (4.6 lb.) |
Operating temperature range |
| 0°C to +40°C |
|
| (+32°F to +104°F) |
Operating humidity range | 35% to 80% RH (no condensation) | |
|
| |
Power consumption in standby mode | 0.1 W (approximate) | |
|
|
|
Note:
1)Specifications are subject to change without notice. Mass and dimensions are approximate.
2)Total harmonic distortion is measured by the digital spectrum analyzer.
10