7

FCC and IC STATEMENT

This equipment has been tested and found to comply with the limits for an Other Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the Panasonic Service Center or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, follow the attached installation instructions and use only shielded interface cables
when connecting to peripheral devices. Any changes or modifications not expressly approved by Panasonic Corp. of
North America could void the user’s authority to operate this device.
FCC and Industry Canada (IC) RF Exposure Warning :
• This TV is provided with two USB ports on rear enclosure for exclusive dedicated use for insertion of the following
optional transmitters: (1) Wireless LAN Adapter with FCC ID:H8N-WLU5150/IC ID:1353A-WLU5150; and (2) Bluetooth
Adapter with FCC ID:NKR-DBUBP207/IC ID:4441A-DBUBP207.
• Other transmitters shall not be used, unless specifically recommended when they become available. Other third-
party wireless transmitters have not been RF exposure evaluated for use with this TV and may not comply with FCC
and IC RF exposure requirements.
• The above two described transmitters comply with FCC and IC radiation exposure limits set forth for an
uncontrolled environment for mobile use with minimum 8 inches (20 cm) spacing requirement between transmitters
and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.
<Only for Wi-Fi if capable of transmission in the 5.15 ~ 5.25 GHz frequency band>
This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful
interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65
to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.
Responsible Party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Contact Source: Panasonic Consumer Marketing Company of North America
1-877-95-VIERA (958-4372)
email: consumerproducts@panasonic.com
This device complies with Part 15 of the FCC Rules and all applicable IC RSS standards.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
■About built-in wireless LAN/Bluetooth

●To use the built-in wireless LAN, an access point needs to be obtained.

●Do not use the built-in wireless LAN to connect to any wireless network (SSID*

1
) for which you do not have usage
rights. Such networks may be listed as a result of searches. However, using them may be regarded as illegal access.

●Check that the Access point supports WPS*

2
.
(If it does not support WPS, the encryption key of the Access point is required when configuring settings.)

●Follow the instructions on the Access point setup screen and configure the appropriate security settings.

For more details on setting of Access point, please refer to operating manual for the Access point.

●We recommend using 11n (5 GHz) for the wireless system between the built-in wireless LAN and Access point.

Communication is also possible with 11a, 11b, and 11g (2.4 GHz), but the communication speed may be slower.

●

If the wireless system of the Access point is changed, devices that could connect by wireless LAN may no longer be able to connect.

●Data transmitted and received over radio waves may be intercepted and monitored.

●Keep the TV away from the following devices as much as possible:

Wireless LAN, microwaves, and other devices that use 2.4 GHz and 5 GHz signals. Otherwise, the TV failures such as
malfunction may occur due to the radio wave interference.

●When noises occur due to the static electricity, etc., the TV might stop operating for the protection of the devices. In

this case, turn the TV Off with power On / Off switch, then turn it On again.
*
1
SSID is a name for identifying a particular wireless network for transmission.
*
2
WPS: Wi-Fi Protected Setup