Technical Information (Continued)
Input signal that can be displayed
* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC
horizontal frequency (kHz)
vertical frequency (Hz)
COMPONENT HDMI
PC
525 | (480) /60i |
| 15.73 | 59.94 | * | * |
| |
525 | (480) /60p | 31.47 | 59.94 | * | * |
| ||
750 | (720) /60p | 45.00 | 59.94 | * | * |
| ||
1,125 | (1,080) | /60i | 33.75 | 59.94 | * | * |
| |
1,125 | (1,080) | /60p | 67.43 | 59.94 |
| * |
| |
1,125 | (1,080) | /60p | 67.50 | 60.00 |
| * |
| |
1,125 | (1,080) | /24p | 26.97 | 23.98 |
| * |
| |
1,125 | (1,080) | /24p | 27.00 | 24.00 |
| * |
| |
640 | × 480 @60 | 31.47 | 59.94 |
|
| * | ||
852 | × 480 @60 | 31.44 | 59.89 |
|
| * | ||
800 | × 600 @60 | 37.88 | 60.32 |
|
| * | ||
1,024 | × 768 @60 | 48.36 | 60.00 |
|
| * | ||
1,280 | × 768 @60 | 47.78 | 59.87 |
|
| * | ||
1,280 | × 1,024 @60 | 63.98 | 60.02 |
|
| * | ||
1,366 | × 768 @60 | 48.39 | 60.04 |
|
| * | ||
Note
Signals other than above may not be displayed properly.
The above signals are reformatted for optimal viewing on your display.
PC Input Terminals Connection
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with IBM PC/AT compatible
If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. Signal Names for
|
|
|
| Pin No. | Signal Name | Pin No. | Signal Name | Pin No. | Signal Name |
5 | 4 | 3 | 2 | 1 | R |
| GND (Ground) |
| NC (not connected) |
10 | 9 |
| 8 | 7 6 | G |
| GND (Ground) |
| NC |
15 14 | 13 | 12 | 11 | B |
| GND (Ground) |
| HD/SYNC | |
|
|
|
|
| NC (not connected) |
| NC (not connected) |
| VD |
Pin Layout for PC Input Terminal | GND (Ground) |
| GND (Ground) |
| NC | ||||
VIERA LinkTM “HDAVI ControlTM”
HDMI connections to some Panasonic equipment allows you to interface automatically. 
This function may not work normally depending on the equipment condition.
The equipment can be operated by other remote controls with this function on even if TV is in Standby mode.
Image or sound may not be available for the first few seconds when the playback starts.
Image or sound may not be available for the first few seconds when Input mode is switched.
Volume function will be displayed when adjusting the volume of the equipment.
If you connect equipment that has “HDAVI Control 2 or later” function to the TV with HDMI cable, the sound from DIGITAL AUDIO OUT terminal can be output as multi channel surround.
“HDAVI Control 5” is the newest standard for the HDAVI Control compatible equipment. This standard is compatible with the conventional HDAVI equipment.
22
