■
Attaching the Supplied Sun Shield
Attach the sun shield to the camera head by
tightening the four supplied screws.
Caution: Be sure to use the four supplied
screws.
SD
II
WV-CW374
FRONT
Aim the arrow to
this direction.
Camera head
Sun shield
Fixing screws
(Supplied) x 4
(M3 x 6)
■
Attaching the Supplied Mounting Adapter
If you use a camera mounting arm locally procured, you need to use the supplied mounting adapter.
1. Remove the camera neck from the camera
head by loosening the camera neck screws.
2. Attach the supplied mounting adapter to the
camera head by tightening the four supplied
screws.
Cautions:
• Be sure to use the supplied screws. Longer
screws may damage inner components, or
shorter screws may cause camera drop.
• You cannot use camera neck screws to attach
the mounting adapter to the camera unit.
Notes:
• Lead the cables out of the camera head.
• When separating the camera neck, remove the
panning lock screw and tilting lock screw.
Then, remove the three screws inside the cam-
era neck.
SD
II
WV-CW374
Mounting adapter
(Supplied)
Fixing screws
(Supplied) x 4
(M3 x 8)
Remove the camera neck and
camera neck screws.
■
Specifications
Dimensions: 78 mm (H) x 82 mm (W) x 301 mm (D)
{3-1/16" (H) 3-1/4" (W) 11-7/8" (L)}
Weights: 1.3 kg {2.9 lbs.}
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
■
Standard Accessories
Instructions (this document)............................................................... 1 pc.
Operating Instructions........................................................................ 1 pc.
The following are for installation.
Sun shield........................................................................................... 1 pc.
Mounting arm..................................................................................... 1 pc.
Adapter box........................................................................................1 pc.
Mounting adapter............................................................................... 1 pc.
Cover.................................................................................................. 2 pcs
Fixing screws for camera (M4 x 8) .................................................... 3 pcs.
Fixing screws for adapter box (M4 x 35) ...........................................1 pc.
Fixing screws for adapter box and mounting arm (M5 x 20) ............ 4 pcs.
Fixing screws for covers (M3 x 6) ..................................................... 2 pcs.
Fixing screws for sun shield (M3 x 6) ................................................ 4 pcs.
Fixing screws for mounting adapter (M3 x 8) ....................................4 pcs.
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
Panasonic Digital Communications & Security Company
Unit of Matsushita Electric Corporation of America
Security Systems Group
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern:One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central:1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western:6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2004 © Matsushita Electric Industrial Co., Ltd. All rights reserved.
■
Connections
Perform cable connections by referring the illustrations.

●Video Output Connection

Connect the video output connector to the monitor or other system device with the procured coaxial
cable. The maximum extensible length is shown in the table.
BNC plug
BNC plug
To Video IN (CAMERA IN)
BNC plug
Video Output cable
24 V AC/12 V DC
WV-CW374
Brown (Live/!)
Blue (Neutral/@)
Green/Yellow (GND)
Black (Live)
Gray (Neutral) For heater
(24 V AC only)
1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal
until it has been ascertained that the unit is functioning.
CONNECT THIS TO CLASS 2 POWER SUPPLY ONLY.
2. All interconnecting devices must be UL Listed.
CAUTIONS
3. Connect the video input jack of LCD moni-
tor and the monitor output jack (3.5 mm
{0.14"} diam. minijack) of camera with a 2-
pole cable.
Note: Refer to the illustrations for the width
of plug to be inserted into the video
input jack.
4. Adjust the camera angle by performing 1) to 3).
1) While holding the camera head, loosen the panning lock screw. Panning becomes adjustable.
Then, move the camera head horizontally.
2) While holding the camera head, loosen the tilting lock screw. Tilting becomes adjustable. Then,
move the camera head vertically.
3) After adjustments, tighten the panning and
tilting lock screws.
Notes:
• When loosening the panning and tilt-
ing lock screws, give only one turn.
• While a LCD monitor is connected to
the camera, You cannot check images
on a monitor connected to the video
output cable.
• After adjusting the panning and tilting,
adjust the focus. (Refer to Adjusting
the Focus.)
■
Adjusting the Focus
1. Remove the front cover by loosening the
four fixing screws. Lens focus becomes
adjustable.
2. Adjust the lens zooming by moving the
zooming ring to T (Tele) or W (Wide).
3. Adjust the lens focus by performing 1) to
3).
1) Loosen the focus lock screw.
The focus lever, locked with the focus lock
screw, will be adjustable.
2) Move the focus lever to F (Far) or N (Near).
3) After adjustment, tighten the focus lock
screw.
Note: To change the lens zooming or
focus, perform Step 2 and 3 again.
■
Attaching the Switch, Rear, and Front Covers
Attach the switch, rear, and front covers to the camera with the screws you have removed.

Switch cover attachment

Perform Step 2 of "Adjusting the Camera Angle" reversely.

Rear cover attachment

Perform Step 1 of "Adjusting the Camera Angle" reversely.

Front cover attachment

Perform Step 1 of "Adjusting the Focus" reversely.
Notes:
• The recommended tightening torque of switch cover fixing screws (x 2) and front cover fixing
screws (x 4) is 0.59 Nm {0.43 lb ft.}.
• Tighten the front cover with the fixing screws in the order from qto rtwo times. (Refer to the
illustration.)
9mm {11/32"}
or less 9mm {11/32"}
or less
Straight plug
L-type plug
Tilting lock screw
(Hexagon socket screw)
Panning lock screw
(Hexagon socket screw)
Front cover
Loosen these screws.
q
r
e
w
W
N
FT
Focus lock screw
(Locking the focus lever)
Zooming ring
CAUTION
Fixing screw x 1
Rear cover
Switch cover Fixing screws x 2
Switch cover attachment Rear cover attachment
Front cover attachment
Recommended
maximum
cable length
Type of coaxial
cable
RG-59/U
(3C-2V)
250
825
RG-6/U
(5C-2V)
500
1 650
RG-11/U
(7C-2V)
600
1 980
RG-15/U
(10C-2V)
800
2 640
(m)
(ft)
●Cable Length and Wire Gauge
24 V AC
The recommended cable length and thickness are shown in the table for reference. The voltage
supplied to the power terminals should be within 19.5 V AC and 28 V AC.
Copper wire size
(AWG)
Recommended wire gauge for 24 V AC line.
Length of
Cable
(Approx.)
#24
(0.22 mm2)
20
65
#22
(0.33 mm2)
30
100
#20
(0.52 mm2)
45
160
#18
(0.83 mm2)
75
260
(m)
(ft)
Resistance Ω/ft
Copper wire size
(AWG)
Resistance Ω/m
#24
(0.22 mm2)
0.078
0.026
#22
(0.33 mm2)
0.050
0.017
#20
(0.52 mm2)
0.03
0.010
#18
(0.83 mm2)
0.018
0.006
Resistance of copper wire [at 20 °C (68 °F)]
12 V DC
Use the formula below to calculate the power cable and power supply. The voltage supplied to the
power terminals of the camera should be within 10.5 V DC and 16 V DC.
10.5 V DC ≤VA - 2(R x I x L) ≤16 V DC
L : Cable length (m) (ft)
R : Resistance of copper wire (Ω/m) (Ω/ft)
VA : DC output voltage of power supply unit
I : DC current consumption (A). See specifications.