ParaBody ex 350 manual TOP Section, Refer to ASSEMBLYDRAWING#4 for Steps 14, Detail a

358 EX350 ASSE~.,IBLY INSTRUCTIONS

Attach BACK/SEATSUPPORT ASSEMBLYto WEIGHTSTACK SUPPORT BASE, u~ing one (1)

I/2 X 3-1 '4 IN. HEXHEADBOLTand one (1) I/2 IN. LOCKNUT(TIGHTEN.ONLYUNTIL SNUG)

.Attach one (1) 4-1.'20.D. DIA. [~ULLEYwith'l IN. BUSHINGinto FRONT"U" PULLEYBRACKET of the BACK/SEATSUPPORT,using one (1) 3/8 X 1-3/4 IN. HEXHEADBOLTand one (1) 3/8

LOCKNUT...

Attach one (I) 4-I;20.D.D1A. PULLEY,with 2 IN. BUSHING,between two fiats on MAINUPRIGHT

TOPSECTIONusln,. ..., one (I) 3/$ X 3 IN. HEXHEADBOLTand one (I) ,~/g IN. LOCKNUT.

10.Slide two (2) 7 3 "8 IN. VINYL SLEEVESover PRONGSof LAT BARHOOKon MAINLrPRIGHT

TOP SECTION.

1i. Attach one (!) 3-1;20.D. DIA. PULLEYwith 1 IN. BUSHING.into PULLEYHOUSINGonMAIN

UPRIGHTTOP SECTION.usingone ([) 3/$X 1-314IN.HEX HEADBOLTand one (I) 318

LOCKNUT. (SEE DETAIL "B" ON DRAWING) (DO NOT TIGHTEN)

12.Bolt MAIN UPRIGHTBOTTO~I SECTION to rear of WE~[GHTSTACKSUPPORTBASE, using two (2) I;2 X 3 IN. HEXHEADBOLTSand two (2) 1/2 IN. LOCKNUTSO'IGHTEN.ONLYUNTIL SNUG)

Bolt MAIN UPRIGHT TOP SECTION to BACKS,E, AT SUPPORT (FIRST INSERT TAB ON BOTTOMSE.CTION INTO THE ENDOF TOP SECTION.). using two (2) 1/2 X 3 IN. HEX HEAD BOLTSand two (2) 1 2 IN. LOCKNUTS.

*** REFER TO ASSEMBLYDRAWING#4 FOR STEPS 14 AND 15 ***

14.Insert two {2) 2 IN. SO. ENDCAPSinto each end oftheBEARINGHOUSING.

SECURELYAssemble the BEARING HOUSING and PULLEY BRACKETSUPPORT to the MAIN UPRIGHTas. shown on drawing, using two (2) 1/2 X 3-1/4 IN. HEXHEADBOLTSand '~,vo (2) 1/2

LOCKNUTS. NOTE: MAKESURE THE TOP AND BOTTOMUPR.IGHT FIT TOGETI--IER BEFORE TIGHTENING.

*** REFERTO ASSEMBLYDRAWING#I FOR STEPS 16 THRU 26 ***

16.Snap two (2) WEIGHTPLATEBUSHINGSinto.each of the fifteen (I5) WEIGHTPLATES.

DETAIL A)

17.Place two (2) WEIGHTSTACKSPACERSover large holes in WEIGHTSTACKSUPPI~RT BASE.

18.Place t~o (2) 3 4 IN. WASHERSover WEIGHTSTACKSPACERS.

19..Place two (2) WEIGHT.STACKCUSHIONSove~" 3/4 IN. WASHERS.

Insert each of the t~xo 12 GUIDERODSthrough the WEIGHTSTACKCUSHIONSand into the

WEIGHT STACK SUPPORT BASE. (.NOTE: LUBRICATE GUIDE RODS WITH A SILICON OR TEFLON SPRAY THAT IS AVAILABLE AT tMOST HARDWARESTORES.}