SET UP

X amplifiers run at about the same power as their output rating, and XA amplifier run more than twice that. The heat sinks on the side of the amplifier run hot to the touch – about 25 to 30 degrees C. above ambient, so you can expect 50 to 55 degrees C. temperatures on the heat sinks. It is very important to the long life of the amplifier that they get good ventilation.

You can put this amplifier anywhere you want, but it must have good ventilation. Do not place it in enclosed cabinets or small closets without means for air to circulate freely. Stacking these power amplifiers directly upon each other is not recommended for the same reason. You should have a minimum of about 6 inches clearance to the top and sides for adequate air circulation.

When not actually intending to play music the amplifier should be left in standby mode, where it draws only a few watts of bias on the output stage. If you wish to reduce the power draw to 0, you can shut the amplifier off via the rear panel switch, however we recommend that for minimum noise this switch should be toggled in stand-by mode.

We have provided a standard IEC power cord that fits into the standard 15 amp IEC receptacle at the rear of the amplifier chassis.

With the exception of the largest of the X and XA series, there is no difficulty running two amplifiers on a single 15-amp circuit. Given the high current draw, we generally do not recommend active line conditioners, although they are unlikely to damage the amplifier.

This amplifier is equipped for operation with an earth ground provided by the users AC outlet. Never defeat this ground connection. The signal ground of this amplifier is connected to earth through a power thermistor, which provides a safety ground but provides isolation from system ground loops.

For maximum safety we suggest that the power cord should be the last cable installed on your power-amplifier. You may, if you wish, substitute a 15-amp aftermarket power cord for the one we have supplied. Only use power cords, which meet all local safety standards and carry acceptance marks from the local regulatory authority. The power cord should be attached to the amplifier prior to plugging into house power. Place the rear mounted switch in the off (down) position before plugging in this amplifier.

XA30.5 Owner’s Manual

5

Page 5
Image 5
Pass Labs Amplifier, 5XA30.5 owner manual Set Up

Amplifier, 5XA30.5 specifications

Pass Labs has long been synonymous with high-performance audio amplification, and their 5XA30.5 amplifier is a testament to their commitment to quality and engineering excellence. The 5XA30.5 is an exceptional Class A amplifier designed for audiophiles seeking purity in sound reproduction. One of its standout features is its power output; delivering 30 watts per channel into 8 ohms and a doubled output into 4 ohms, it provides ample power for driving a range of loudspeakers with ease.

One of the key technologies employed in the 5XA30.5 is its Class A circuitry. Unlike other amplification classes that switch on and off to produce sound, Class A amplifiers operate continuously, ensuring that the signal remains uncorrupted. This results in a rich, warm sound that faithfully represents the original recording. The design eliminates crossover distortion, a common issue in other classes of amplification, thus enabling the 5XA30.5 to deliver detailed and smooth audio performance, even at lower volumes.

The amplifier's robust construction further enhances its performance. With a fully balanced differential input stage, the 5XA30.5 minimizes noise and distortion, ensuring that the sound remains crisp and clear. The use of custom-designed output transistors offers superior linearity and thermal stability. Additionally, the generous power supply, equipped with a hefty transformer and ample capacitance, allows the amplifier to handle dynamic peaks without strain, preserving the integrity of the audio signal.

Another notable characteristic of the 5XA30.5 is its elegant design. The aesthetics include a minimalist chassis, machined aluminum front panel, and dual meters that provide real-time performance feedback, allowing audiophiles to observe the amplifier’s operation. Furthermore, it features both single-ended and balanced inputs, offering compatibility with a variety of source components.

Importantly, the 5XA30.5 embodies Pass Labs' philosophy of "the art of amplifier design," resulting in a product that not only performs exceptionally well but also maintains a timeless appeal. Whether for critical listening or enjoying music in a relaxed setting, the Pass Labs 5XA30.5 amplifier promises an unparalleled auditory experience, fulfilling the demands of even the most discerning audiophile. In a landscape where many amplifiers prioritize features over fidelity, the 5XA30.5 remains a beacon of true sound reproductions, demonstrating that exceptional quality and craftsmanship can coexist harmoniously.