5.2.2 REMOTE ANALOG LOOP
The second test mode is Remote Analog Loop. To enter this mode, set one of the Model 1050s (local) in test mode by depressing the "Loopback Test" switch. Any characters sent from the remote 1050 will be returned to it (see Figure 5). If no characters are echoed back, check the wiring between the two Model 1050s. Be sure to wire the units according to the instructions in Section 4.0 Installation.
|
|
|
|
|
|
| TX+ |
|
| RX+ |
|
|
| RD | ||||||||
TD |
|
|
|
|
| TX- |
|
| RX- |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
| RX- |
|
| TX- |
|
|
| TD | ||||||||
RD |
|
|
|
|
|
| RX+ |
|
| TX+ |
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Local 1060 |
| Remote 1060 |
|
| |||||||||||||||
|
| In Normal Mode | In Normal Mode |
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| TX+ |
|
| RX+ |
|
| RD | |||||||
TD |
|
|
|
|
|
|
| TX- |
|
|
| RX- |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
| RX- |
|
| TX- |
|
| TD | |||||||
RD |
|
|
|
|
|
|
|
| RX+ |
|
| TX+ |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Local 1060 |
| Remote 1060 |
|
| |||||||||||||||
|
| In Loopback Mode | In Normal Mode |
|
| |||||||||||||||||
Figure 5. Loopback Test Modes
APPENDIX A
PATTON MODEL 1050 SPECIFICATIONS
Transmission Format: Asynchronous
Transmission Line: | 19 to 26 AWG twisted pair |
Range: | 7 miles on 24 AWG twisted pair @ 1200 bps |
Serial Interface: | EIA |
Twisted Pair Interface: Terminal blocks, | |
Data Rates: | 0 - 38,400 bps |
Applications: | |
Indicators: | |
| test |
Diagnostics: | Local Analog Loopback (LAL), Remote |
| Analog Loopback (RAL) |
Optical Isolation: | 2500V RMS (minimum) |
Power Supply: | Wall mount, |
Temperature Range: | |
Altitude: | |
Humidity: | 5 to 95% noncondensing |
Dimensions: | 1.58”H x 4.16”W x 3.75”D |
Weight: | 13.2 oz. (without transformer) |
11 | 12 |
