1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1110 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above. Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product. Patton Electronics specifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1110 generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television reception. The Model 1110 has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the Model 1110 does cause interference to radio or television reception, which can be determined by disconnecting the RS-232 interface, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).

1.2 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Service at (301) 975-1007. Packages received without an RMA number will not be accepted.

Patton Electronics’ technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 1110. Technical Service hours: 8AM to 5PM EST, Monday through Friday.

1

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Year parts and labor. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics Technical Support at (301) 975-1007.

2.1FEATURES

Communicates over dual optical fibers

Data rates to 19.2 Kbps

Distances to 1 mile

Plugs directly into an RS-232 port

Immune to RFI/EMI noise, ground loops and transient surges

Easily accessible DCE/DTE switch

DIP Switch-selectable carrier control

Requires no AC power or batteries

Two easy-to-read status indicators

Fits into tight installation spaces

Male or female DB-25 and SMA or ST connectors available

2.2DESCRIPTION

The Patton Model 1110 miniature RS-232 fiber optic modem brings fiber to the desktop. Communicating over dual optical fibers, the Model 1110 supports data rates to 19.2 Kbps and distances to 1 mile. The Model 1110 operates full or half duplex and plugs directly into a workstation’s RS-232 port.

Like all fiber optic modems, the Model 1110 is inherently immune to RFI/EMI noise, ground loops and transient surges. The carrier may be switch selected as either “Continuously On” or “Controlled by RTS”, while an easily accessible DCE/DTE switch eliminates the need for cumbersome RS-232 crossover cables. Two easy-to-read LED indicators monitor the status of carrier detect and fiber optic output. Drawing all necessary power from the RS-232 interface, the Model 1110 requires no AC power or batteries to operate.

Measuring only 2.66” x 2.10” x .73”, the Model 1110 is able to fit into tight installation spaces. A convenient pop-open/snap-shut ABS plastic case allows easy access to configuration switches. On the RS-232 side, the Model 1110 comes equipped with either a male or female DB-25 connector; on the fiber side, it is available with a choice of SMA or ST connectors.

2

Page 2
Image 2
Patton electronic 1110 user manual Radio and TV Interference, Service, Features, Description