Manuals
/
Patton electronic
/
Computer Equipment
/
Switch
Patton electronic
2174 user manual Copyright Patton Electronics Company All Rights Reserved
Models:
2174
1
24
24
Download
24 pages
22.58 Kb
17
18
19
20
21
22
23
24
<
>
Install
Line Rate & Reach Chart, Based on 24 AWG 0.5 MM
Warranty
Dimension
Configuration
Connecting The Line Interface
Switch S1-5 General Protection Signal to Noise Ratio
How to
Power
D R M Green European Compliance Services Limited
Page 24
Image 24
Copyright © 2011.
Patton Electronics Company
All Rights Reserved.
24
Page 23
Page 24
Image 24
Page 23
Contents
USER MANUAL
MODEL
CopperLINK High Speed Ethernet Extender
An ISO-9001Certified Company
CONTENTS
Warranty Information
Installation
Configuration
Line Rate & Reach Chart, Based on 24 AWG 0.5 MM
RJ-45
C.2 CopperLINK Interface
RJ-45
1.0 WARRANTY INFORMATION
Low-Voltage Direcive Safety
1.1 REGULATORY INFORMATION EMC Directive
PSTN
1.5 SERVICE
1.3 CE DECLARATION OF CONFORMITY
1.4 AUTHORIZED EUROPEAN REPRESENTATIVE
Tel +1 301 Email support@patton.com
1.6 SAFETY WHEN WORKING WITH ELECTRICITY
For AC powered devices which have 3 conductor
power plugs L1, L2 & GND or Hot, Neutral
must have an earth ground
Electrostatic Discharge ESD can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the fol- lowing to prevent ESD
2.1 FEATURES
2.0 GENERAL INFORMATION
2.2 DESCRIPTION
3.0 INSTALLATION The Interconnecting cables shall be acceptable for
CAUTION perature, flammability, and mechanical serviceability
external use and shall be rated for the proper applica
tion with respect to voltage, current, anticipated tem
Figure 2. Model 2174 rear panel options
Eth3 Eth2 Eth1 Eth0
Eth3 Eth2 Eth1 Eth0
Eth3 Eth2 Eth1 Eth0
3.1 CONNECTING THE LINE INTERFACE
The Interconnecting cables shall be acceptable for
Connecting the Line Interface for Model 2174/EUI or 2174/TB
CAUTION perature, flammability, and mechanical serviceability
Connecting the Line Interface for Model 2174/BNC
3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE
1 TX+/RX+
2 TX-/RX
3.3 CONNECTING POWER
4.0 CONFIGURATION
4.1 CONFIGURING THE HARDWARE DIP SWITCHES
The Interconnecting cables shall be acceptable for
4.2 CONFIGURING DIP SWITCH S1
Position
Description
S1 Switch toggle
Switch S1-1 Local/Remote Configuration
Setting
Switches S1-2 and S1-3 Symmetric/Asymmetric Operation
Switch S1-5 General Protection Signal to Noise Ratio
Power
5.0 OPERATION
5.1 FRONT PANEL LED STATUS MONITORS
Status
A.4 LED STATUS INDICATORS
A.5 POWER SUPPLY
A.6 TEMPERATURE RANGE
A.8 DIMENSIONS
APPENDIX B
Patton Model #
Power Supplies
Power Adapters
APPENDIX C
C.1 10/100BASE-T INTERFACE RJ-45
C.2 COPPERLINK INTERFACE RJ-45
Terminal Block
APPENDIX D
Mode
Distance in Feet
Mbps
High Speed
Table 7 Line Rate & Reach Chart Using Twisted-Pair High Speed
Mode
Distance in Feet
Page
Page
Copyright Patton Electronics Company All Rights Reserved
