Manuals / Patton electronic / Computer Equipment / Switch

Patton electronic 2174 Line Rate & Reach Chart, Based on 24 AWG 0.5 MM, RJ-45, Terminal Block

Models: 2174

1 24

Page 3

RJ-45	19
C.2 CopperLINK Interface	19
RJ-45	19
Terminal Block	19
D
Line Rate & Reach Chart, Based on 24 AWG (0.5 MM)	20

Page 3

Image 3

Patton electronic 2174 Line Rate & Reach Chart, Based on 24 AWG 0.5 MM, RJ-45, C.2 CopperLINK Interface, Terminal Block

Contents

An ISO-9001Certified Company USER MANUALMODEL CopperLINK High Speed Ethernet ExtenderConfiguration CONTENTSWarranty Information InstallationRJ-45 Line Rate & Reach Chart, Based on 24 AWG 0.5 MMRJ-45 C.2 CopperLINK InterfacePSTN 1.0 WARRANTY INFORMATIONLow-Voltage Direcive Safety 1.1 REGULATORY INFORMATION EMC DirectiveTel +1 301 Email support@patton.com 1.5 SERVICE1.3 CE DECLARATION OF CONFORMITY 1.4 AUTHORIZED EUROPEAN REPRESENTATIVEmust have an earth ground 1.6 SAFETY WHEN WORKING WITH ELECTRICITYFor AC powered devices which have 3 conductor power plugs L1, L2 & GND or Hot, NeutralElectrostatic Discharge ESD can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the fol- lowing to prevent ESD 2.1 FEATURES 2.0 GENERAL INFORMATION2.2 DESCRIPTION tion with respect to voltage, current, anticipated tem 3.0 INSTALLATION The Interconnecting cables shall be acceptable forCAUTION perature, flammability, and mechanical serviceability external use and shall be rated for the proper applicaEth3 Eth2 Eth1 Eth0 Figure 2. Model 2174 rear panel optionsEth3 Eth2 Eth1 Eth0 Eth3 Eth2 Eth1 Eth0CAUTION perature, flammability, and mechanical serviceability 3.1 CONNECTING THE LINE INTERFACEThe Interconnecting cables shall be acceptable for Connecting the Line Interface for Model 2174/EUI or 2174/TB2 TX-/RX Connecting the Line Interface for Model 2174/BNC3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE 1 TX+/RX+The Interconnecting cables shall be acceptable for 3.3 CONNECTING POWER4.0 CONFIGURATION 4.1 CONFIGURING THE HARDWARE DIP SWITCHESS1 Switch toggle 4.2 CONFIGURING DIP SWITCH S1Position DescriptionSwitch S1-5 General Protection Signal to Noise Ratio Switch S1-1 Local/Remote ConfigurationSetting Switches S1-2 and S1-3 Symmetric/Asymmetric OperationStatus Power5.0 OPERATION 5.1 FRONT PANEL LED STATUS MONITORSA.8 DIMENSIONS A.4 LED STATUS INDICATORSA.5 POWER SUPPLY A.6 TEMPERATURE RANGEPower Adapters APPENDIX BPatton Model # Power SuppliesTerminal Block APPENDIX CC.1 10/100BASE-T INTERFACE RJ-45 C.2 COPPERLINK INTERFACE RJ-45Mbps APPENDIX DMode Distance in FeetDistance in Feet High SpeedTable 7 Line Rate & Reach Chart Using Twisted-Pair High Speed ModePage Page Copyright Patton Electronics Company All Rights Reserved

RJ-45

C.2 CopperLINK Interface

Terminal Block

Line Rate & Reach Chart, Based on 24 AWG (0.5 MM)