Peavey EVH 5150 II Power Amplification Section, Specifications Preamp Section, Block Diagram

POWER AMPLIFICATION SECTION

RATED POWER AND LOAD:

120 W RMS into 16, 8, or 4 ohms

POWER @ CLIPPING:

(Typically @ 5% THD, 1 kHz, 120 V AC line)

130 W RMS into 16, 8, or 4 ohms (Bias must be reduced to measure.)

FREQUENCY RESPONSE:

+0, -3 dB, 50 Hz to 20 kHz @ 100 W RMS into 8 ohms

HUM AND NOISE:

Greater than 75 dB below rated power

POWER AMP EQ:

Active Presence: +10 dB @ 2 kHz

Active Resonance: +10 dB @ cabinet resonant frequency

POWER CONSUMPTION (Domestic):

400 watts 50/60 Hz, 120 V AC (Domestic)

TUBE COMPLEMENT:

5150® II

SPECIFICATIONS PREAMP SECTION

The following specs are measured @

1 kHz with the controls preset as follows: Low and High EQ @ 10

Mid EQ @ 0 Bright out

Lead and Rhythm Posts @ 10

Presence and Resonance @ 0 dB Nominal levels with Pre Gains @ 5 Minimum levels with Pre Gains @ 10

PREAMP INPUT:

Impedance: Very high Z, 470K ohms

Lead Channel (with channel select in): Nominal Input Level: -60 dBV,

1 mV RMS

Minimum Input Level: -76 dBV,

.15 mV RMS

Clean Channel (with channel select out): Nominal Input Level: -30 dBV,

30 mV RMS

Minimum Input Level: -34 dBV,

20 mV RMS

Maximum Input Level: 0 dBV,

1.0 V RMS

(Subtract 24 dB with Crunch switch in.)

EFFECTS RETURN:

Impedance: Very High Z, 470 k ohms

Designed Level: -10 dBV, 300 mV RMS

PREAMP OUT:

Load Impedance: 47 k ohms or greater

Nominal Output: +10 dBV, 3 V RMS

REMOTE FOOTSWITCH:

Special 3-button unit with LED indicators (supplied)

Channel select and reverb

SYSTEM HUM AND NOISE @ NOMINAL LEVEL (clean channel):

(20 Hz to 20 kHz unweighted) Greater than 63 dB below rated power

EQUALIZATION:

Custom Low, Mid, and High passive type EQ

Push Bright (Rhythm Channel only) +6 dB @ 2 kHz

Push Crunch (Rhythm Channel only) Increases gain

DIMENSIONS (H x W x D):

10" x 26.625" x 11.75"

(25.4 cm x 67.6 cm x 29.8 cm

6-12AX7 preamp tubes

(1 for clean/crunch, 3 for Lead, 1 for EFX and 1 phase splitter 4-6L6GC

EFFECTS SEND:	WEIGHT:
Load Impedance: 47 k ohms or greater	48.3 lbs. (21.91 kg)
Nominal Output: -10 dBV, 300 mV RMS

Features and specifications subject to change without notice.

5150® II

BLOCK DIAGRAM

	PRE	LOW MID HI POST
LEAD	TUBE STAGES	FOOTSWITCH

		FOOTSWITCH		SWITCH
				LOGIC
INPUT	SWITCH
				TUBE BUFFER
TUBE STAGE		LOGIC
		CHANNEL
		SELECT
				TUBE STAGES
RHYTHM		TUBE STAGES
		PRE	LOW MID HI	POST
		PUSH	PUSH	TUBE
		BRIGHT	CRUNCH	POWER
				AMP
		FOOTSWITCH
				SWITCH
				LOGIC
				PREAMP
				OUT

EFFECTS

SEND

RETURN

SPEAKER

OUTPUTS

IMPEDANCE

SWITCH

RESONANCE PRESENCE	RESONANCE PRESENCE
LEAD	RHYTHM

7