REAR PANEL
|
|
|
|
|
|
|
|
|
| WARNING:TO REDUCE THE RISK OF |
|
|
|
|
|
|
|
|
|
| FIRE OR ELECTRIC SHOCK DO NOT EXPOSE |
|
|
|
|
|
|
|
|
|
| THIS EQUIPMENT TO RAIN OR MOISTURE. |
|
|
|
|
|
|
|
|
|
| TO PREVENT THE RISK OF FIRE HAZARD, |
|
|
|
|
|
|
|
|
|
| REPLACE WITH SAME TYPE 250 VOLT FUSE. |
|
|
|
|
|
|
|
|
|
| AVIS:RISQUE DE CHOC ELECTRIQUE - |
|
| 120V | 60Hz/230V | 50Hz | NE PAS OUVRIR. REMPLACER PAR UNFUSI- | |||||
|
| BLE DE MEME TYPE ET DE 250 VOLTS. | ||||||||
230V |
|
|
| 20 WATTS |
|
| ||||
| 115 |
|
|
| FUSE |
|
| |||
115V |
|
|
|
| E F |
|
|
| ||
|
|
|
| SU |
|
| ||||
|
|
|
| F 500 mA |
| A PRODUCT OF PEAVEY ELECTRONICS CORP. | ||||
|
|
|
|
| 250V |
| ||||
|
|
|
|
|
| MERIDIAN MS. | ||||
|
|
|
|
|
|
|
|
|
| |
1 |
| 4 |
|
| 2 |
| ||||
ONE | TM |
|
|
|
|
|
|
|
|
OUTPUT | CHANNEL | CHANNEL | CHANNEL | CHANNEL |
| ||||
|
|
| FOUR | THREE | TWO | ONE |
| ||
P R O D U C T I O N | REC | AMP | LINE 5 | LINE 4 | LINE 3 | LINE 2 PHONO 2 | LINE 1 | PHONO 1 |
|
M I X E R |
|
|
|
|
|
|
| GND | MIC 2 |
| L |
| L | L | L | L |
| L |
|
| R |
| R | R | R | R |
| R |
|
| 5 | 6 |
|
| 7 |
|
| 8 | 10 |
DESCRIPTIONS
POWER
The PM One is supplied with a switchable power supply. Before plugging your PM One in, please read this entire section to ensure proper supply voltage selection and unit operation. It is important that all safety precautions be followed.
1.VOLTAGE SELECTOR SWITCH
Use this switch to select the proper AC supply voltage for your area. This voltage varies from one
geographical area to another. For voltages between 110 and 120 VAC, select the 115 position. For voltages between 220 and 230 VAC, select the 230 position.
2.IEC POWER CORD
This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used. (See voltage marking on unit.) Never remove or cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord. When lost or damaged, replace this cord with one of the proper ratings.
NOTE: FOR UK ONLY
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored green and yellow must be connected to the terminal which is marked by the letter E or by the earth symbol or colored green or green and yellow. (2) The wire which is colored blue must be connected to the terminal which is marked with the letter N or the color black. (3) The wire which is colored brown must be connected to the terminal which is marked with the letter L or color red.
3.POWER ON/OFF SWITCH and LED
The Power On/Off Switch is located on the front of the PM One. (Top panel. See diagram on page 6.) This switch in the (l) position will turn the unit on if proper voltage is supplied. The power LED located next to the switch will illuminate when the unit is on. WARNING: PROPER VOLTAGE MUST BE SELECTED BY THE VOLTAGE SELECTOR SWITCH (1) BEFORE THIS SWITCH IS TURNED ON. FAILURE TO SELECT THE PROPER VOLTAGE APPLICABLE TO YOUR POWER SOURCE COULD RESULT IN DAMAGE TO YOUR PM ONE MIXER.
4.FUSE (0.5A/250V)
The fuse is located within the cap of the fuseholder (on back panel). If the fuse should fail, IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the unit repeatedly blows fuses, it should be taken to a qualified service center for repairs.
WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE.
4
